Kyocera KM-C2030 Fiery X3e Configuration Guide for Ver 2.0
Kyocera KM-C2030 Manual
View all Kyocera KM-C2030 manuals
Add to My Manuals
Save this manual to your list of manuals |
Kyocera KM-C2030 manual content summary:
- Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 1
Fiery X3e CONFIGURATION GUIDE - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 2
to monitor and control jobs on the Fiery X3e. This manual is intended for an operator or administrator, or a user with the necessary access privileges, who monitors and manages job flow, performs color calibration, and troubleshoots problems that may arise. • Release Notes provide last-minute product - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 3
For Imaging, For Imaging, Imaging, Inc. Color Profiler, EFI Production System, EFI ScanBuilder, Fiery X2, Fiery X2e, Fiery X2-W, Fiery X3e, Fiery X4, Fiery ZX, Fiery Z4, Fiery Z5, Fiery Z9, Fiery Z16, Fiery Z18, Fiery Document WorkStation, Fiery Downloader, Fiery Driver Imaging Imaging's standard - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 4
and used in accordance with the instruction manual, may cause harmful interference to radio in other installations. It is the user who is responsible for compliance of his thereof, except as necessary for backup or archive purposes in support of your use of the Software as permitted hereunder. You - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 5
only to authorized users having a need the Software will be uninterrupted or error free, or that all defects in WITH YOU, AND EFI SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY shall not be subject to the United Nations Convention on Contracts for the Imaging 303 Velocity Way Foster City, CA 94404 - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 6
- Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 7
Contents About the Documentation Introduction About this manual xi Chapter 1: Connecting to the Network Fiery X3e on the 16 Tips for experts-UNIX workstations 2-16 Important note about the remote printer name 2-17 Setting up the Fiery X3e on TCP/IP networks 2-17 Managing print jobs 2- - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 8
of Setup screens 4-4 Server Setup options 4-4 Network Setup options 4-7 Port Setup options 4-9 Protocol Setup options 4-11 Service Setup options 4-17 Printer Setup options 4-35 PostScript Setup options 4-37 PCL Setup options 4-39 Color Setup options 4-41 PrintMe Setup options - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 9
Setup 5-1 Remote Fiery Setup 5-1 General Setup options 5-3 Job Log Setup 5-5 Network Setup 5-6 Adapters/Ports 5-7 Protocols 5-9 Services 5-14 Windows print sharing with Server Message Block (SMB) 5-24 Printer Setup options 5-30 Printer connections 5-30 PS (PostScript) Setup - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 10
Shutting down, rebooting, and restarting the Fiery X3e 7-10 Shutting down and rebooting the Fiery X3e 7-10 Restarting the Fiery X3e 7-12 Appendix A: Troubleshooting Troubleshooting the Fiery X3e A-1 Troubleshooting during Setup from the Control Panel A-1 Runtime error messages A-7 Index - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 11
sent by users from remote workstations. Any additional connectivity or administrative features specific to the copier are described in the Printing Guide or the Release Notes. About this manual This manual covers the following topics: • Basic configuration of the Fiery X3e to support printing over - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 12
environments NOTE: The network guidelines in this book are not intended to replace the services of an experienced network engineer. This manual is organized as follows: • Chapter 1 illustrates the supported network configurations and shows the network connectors on the Fiery X3e. • Chapter 2 provides - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 13
and includes diagrams that refer you to other chapters or other manuals for completing your installation. Check those references to find the network, it behaves as a networked PostScript printer. The built-in Ethernet interface on the Fiery X3e supports the following network protocols: • AppleTalk • - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 14
X3e as a PCL or PostScript printer. For information on configuring User Software Installation Guide, and some information is also provided in Chapter 2. • Administering the Fiery X3e Monitor and maintain system performance and troubleshoot problems that arise. For details, see Chapter 7 of this manual - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 15
On the Fiery X3e Control Panel, configure, at a minimum, the Server Setup, Network Setup, and Printer Setup. Configure the remaining Setups. At each computer from which users print to the Fiery X3e: • Install the appropriate printer files and connect to one or more queues. • Install Fiery® utilities - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 16
setup procedures referenced in the "Key to setup" in the upper-left corner of each diagram. The diagrams describe devices that use the supported the scope of this manual. If your network uses more than one protocol or more than one type of workstation, combine the setups listed for each component - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 17
11-5 Quick path to installation Key to setup: 1 Mac OS computer 2 Fiery Setup Mac OS environment with AppleTalk User Software Installation Guide Chapter 4 Fiery X3e installed in the copier 2 TCP/IP (http) for WebTools AppleTalk Mac OS computer 1 Mac OS computer 1 Mac OS computers can print - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 18
computers in a Novell environment Key to setup: 1 NetWare server 2 Fiery X3e Setup 3 NetWare client 4 Windows computer with SPX page 2-13 Chapter 4 User Software Installation Guide page 2-8 Another supported protocol Fiery X3e installed in the copier 2 NetWare server 1 IPX TCP/IP (http - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 19
NT 4.0 Server 2 Fiery X3e Setup 3 Windows NT 4.0 client Windows NT 4.0/2000 Server environment page 2-3 Chapter 4 page 2-5 Another supported protocol Windows NT Workstation or Windows NT Server acting as print server 1 LAN with NETBEUI, etc. Fiery X3e installed in the copier 2 TCP/IP (lpd) for - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 20
11-8 Connecting to the Network Key to setup: 1 Windows computer 2 Fiery X3e Setup Windows computers using Windows printing User Software Installation Guide Chapter 4 Another supported protocol Fiery X3e installed in the copier 2 TCP/IP (nbt) Windows computer 1 Windows computer 1 Windows - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 21
2 Fiery X3e Setup 3 UNIX workstation 4 TCP/IP client 5 Windows NT 4.0 client UNIX workstations and Windows computers on a TCP/IP network page 2-16 Chapter 4 page 2-16 User Software Installation Guide, Chapter 4 page 2-5 Another supported protocol Fiery X3e installed in the copier 2 UNIX server - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 22
Key to setup: 1 Fiery X3e Setup 2 Windows computer Fiery X3e parallel port connection Chapter 4 Printing Guide With the parallel port enabled, the Fiery X3e can accept and print jobs sent to its parallel port Parallel A supported network protocol Fiery X3e installed in copier 1 Parallel input - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 23
11-11 Connecting network cable to the Fiery X3e Connecting network cable to the Fiery X3e In this section, the back panel of the Fiery X3e is illustrated, followed by information for connecting to the Ethernet board. Back view of the Fiery X3e Parallel Port RJ-45 Ethernet (10/100Base T) - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 24
an 8-pin RJ-45 connector that plugs into the RJ-45 socket on the Fiery X3e. NOTE: The 100BaseT type supported by the Fiery X3e is 100BaseTX, also known as Fast Ethernet. If an Ethernet hub is used, it must be on the Windows computer. 3. Turn on the computer and the Fiery X3e. 4. Proceed to Setup. - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 25
a network server is optional. This chapter also outlines the requirements for users to print to the Fiery X3e and run Fiery utilities and Fiery TCP/IP, it can print directly to the Fiery X3e. If the computer shares the printer over the network, it is acting as a print server to Windows 9x/Me and - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 26
page 2-17. • For Windows NT 4.0/2000/XP, install the appropriate printer driver files (PCL or PostScript) on the Windows NT 4.0/2000 server. For more information, see the User Software Installation Guide. • Repeat the installation for all users who print to the Fiery X3e. Each server and workstation - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 27
host database used by your system (see page 2-4). • Perform Fiery X3e Setup. • On the Windows NT 4.0/2000 server, create a printer for each Fiery X3e print connection, install the appropriate printer drivers, and (optionally) share the printer on the network (see page 2-4). • Enter the host name and - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 28
). Installing the Fiery X3e as a shared printer The first step in creating a printer is installing the printer driver files, which give your applications access to printer features. You can use the installation instructions in the User Software Installation Guide for every workstation that will print - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 29
files. If you have not yet installed the Fiery X3e printer files on the Windows NT 4.0/2000 print server computer, do so now, following the instructions in the User Software Installation Guide. During installation, enter the information necessary to share the Fiery X3e. If you have already installed - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 30
Servers • For Windows 2000/XP clients: Before printing, install the printer driver with the User Software CD and configure the port. After clients have selected the printer, they can choose it from the Print Setup, Page Setup, or Print dialog box of their application. Clients can change printing - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 31
X3e support the following network operating environments: • NetWare 4.x or 5.x-NDS (Novell Directory Services) • setup and client network setup are outlined in this chapter, client printing setup is described in the User Software Installation Guide, and printing is described in the Printing Guide - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 32
X3e is similar to setting up any other PostScript printer on the network. The Fiery X3e with IPX of IPX printing to the Fiery X3e NetWare file servers support the creation of print queues, which are storage areas for You do not need to rerun Setup when you add or remove a NetWare queue; however, - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 33
sections explain how to set up a NetWare file server so networked users can print to the Fiery X3e from their workstations, and the Fiery server, and print queue for the Fiery X3e (see page 2-12). With bindery services, you can route all Fiery X3e print jobs through the same NetWare file server, - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 34
WorkStation In NETADMIN: Create NDS PQs Create NDS printer and assign PQs Create PS and assign the printer Configure users of the PQs Port Setup Ethernet Setup Protocol Setup IPX/SPX Setup-select frame types Service Setup PServer Setup and NDS Setup Select Root Browse to select PS Specify PQ - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 35
X3e, you are mainly concerned with defining a printer, a print server object, and one or more print same tree as the one you selected in NDS Setup. In order to set up the NetWare 4.x administrator must do the following: • Determine the Directory Services path to the container in which the print server - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 36
client setup printer driver and the Fiery X3e PPD (PostScript printer description). • Adding a network port and connecting the workstation to one or more NetWare queues that have been defined for the Fiery X3e. • Installing Fiery X3e software. For details, see the User Software Installation Guide - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 37
Print Services). For IPX printing, the Fiery X3e supports the PServer service in Bindery emulation or through NDS (Novell Directory Services). For also make the printer driver available for clients to download from Windows 9x/Me and Windows NT 4.0/2000/XP computers. During Fiery X3e Setup, you select - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 38
have manually unloaded the Broker, it loads and runs when you install NDPS. Make sure you are using the latest NetWare 5.x service pack NetWare server for NDPS to install the corresponding printer driver files from the User Software CD. TO SET UP THE PRINTER DRIVER FOR WINDOWS NT 4.0/2000/XP 1. Log - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 39
at your organization, you can set up the Fiery X3e as a Public Access printer or a Controlled Access printer. The following procedure describes setting up a Public Access printer. You can then convert the printer to Controlled Access if necessary. For more information, see your NetWare documentation - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 40
, enter the name of the Fiery X3e print connection you want users to print to, and click Finish. This name must be either print or hold. 10. In the Select Printer Drivers dialog box, select the printer driver for Windows 9x/Me and the driver for Windows NT 4.0/2000/XP. 11. Click Continue, and then - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 41
printer, as the "Name of printer or print queue on that (lpd host) server" in the Add LPR Compatible Printer dialog box. For the Windows 2000/XP printer driver, enter the remote printer name , however, there is no difference in setup except that a client machine does not have its own spooling area. - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 42
network users. 4. To verify the TCP/IP connection, ping the IP address or the host name. From any computer on the network, at the command prompt, type: ping Type the Fiery X3e IP address assigned in Fiery X3e Network Setup. After the Fiery X3e is set up as a network printer, you - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 43
users print from applications, they can set print options with the driver Downloader™ to download Guide. Even without the Fiery utilities, you can: • Set up the Fiery X3e to print a log of printed jobs automatically after every 55 jobs (see Job Log Setup on page 4-48). • Print a Job Log manually - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 44
- Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 45
™. Fiery X3e print connections The Fiery X3e supports three print connections: Hold queue, Print queue, and Direct connection. These print connections can be enabled, or "published," to users on the network when you configure Printer Setup. All published connections are constantly checked for - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 46
to reprint those jobs. In Setup, you can enable the Printed see the Job Management Guide). Print queue This job remains at the user workstation until the Fiery X3e The Direct connection is not supported for LPR printing. Jobs download fonts to the Fiery X3e, you must publish the Direct connection - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 47
fically set passwords, all users will have administrator privileges, which include access to important functions such as Setup (including setting passwords), and Fiery X3e of all job data, performing calibration, defining default color profiles, and setting default values for print options. When - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 48
The Fiery X3e supports Internet or intranet access with WebTools from Windows and Mac OS computers. To enable use of WebTools, you must do the following in Setup: • Enable TCP/IP. • Set an IP address, subnet mask, and gateway address for the Fiery X3e. • Enable Web Services. For more information - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 49
information, see Chapter 5. NOTE: WebSetup is supported on Windows computers only. Installer The Installer WebTool allows users to download installers for printer drivers directly from the Fiery X3e. It is not affected by passwords. For more information, see the User Software Installation Guide. - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 50
to system settings. 1. No designated administrator or operator (Minimum control-not recommended) All users have equal access to all system functions including Setup, clearing the Fiery X3e, deleting printer fonts, setting the WebLink address, performing calibration, printing to all Fiery X3e print - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 51
tools; users can print only to the Hold queue; the administrator and the operator have complete control of job flow; no access to WebTools. Use these settings 1 2 3 4 5 in Setup (Minimum) (Maximum) Enable Direct connection √ √ √ Enable Print queue √ √ √ √ Enable Web Services - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 52
known as SMB printing. NOTE: The Fiery X3e does not support the Windows 2000 Active Directory Service. When you use the Fiery X3e in a Windows 2000 server environment, assign the Fiery X3e to a Domain or Workgroup. Ensuring the copier connection Complete the following steps before you configure the - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 53
33-9 About Setup TO PREPARE FOR FIERY X3E CONFIGURATION 1. Print a copier Test Page to verify the copier is functioning normally. 2. Turn off the copier and connect the interface cable from the copier to the Fiery X3e. 3. To confirm this connection, turn on the copier and the Fiery X3e, and print a - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 54
- Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 55
systems that transmit print jobs to the Fiery X3e • Printer Setup to specify how print jobs and queues are managed • PS Setup to specify PostScript settings • PCL Setup to specify PCL settings • Color Setup to specify color settings • Job Log Setup to specify how the Fiery X3e handles its log of - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 56
44-2 Performing Setup from the Control Panel Utility button Touch Panel Menu button Up and Down arrow buttons The Control Panel on the front of the clothing, wash it off with soap and water immediately. Do not touch or put pressure on the display window. This will change the color of the window. - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 57
window, press the button for the Setup you want to access. For first-time Setup, you must perform at least these Setups in this order: Server Setup, Network Setup, and Printer Setup. After performing these Setups, you can continue with the remaining Setups, or exit Setup and save your changes. About - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 58
your site (the printer name or IP users. To access the menu, follow the instructions on page 4-3. When you choose Server Setup, the options appear in sequence, as follows. Default values, where applicable, appear in square brackets. Words shown in italics indicate that a product- or site-specific - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 59
44-5 Server Setup options Server Name Default server name Enter a name for the Fiery X3e /No [Yes] Specify whether to enable printer groups for Member Printing. If you enable this option, you must use Command WorkStation to define user groups and passwords. Users must then enter their group name and - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 60
Performing Setup from X3e disk for recent jobs that were printed from the Print queue. Users with Administrator or Operator access to the job management tools can reprint jobs remove scanned data from the hard disk. If you select Manually, the scanned data remains on the hard disk until specifically - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 61
you to choose port types, protocols, and network services. You must perform Port Setup and enable at least one port. For each item you enable, you are prompted to enter settings for that item. Default values, where applicable, appear in this manual with square brackets. You should display and select - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 62
Setup Ethernet Setup Ethernet Setup Ethernet Setup Parallel Port Setup Use this Protocol Setup AppleTalk Setup TCP/IP Setup: Ethernet Setup IPX/SPX Setup - Use this Service Setup AppleTalk printing (PAP) is enabled automatically. LPD Setup Web Services Setup Windows Setup Port 9100 Setup IPP Setup - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 63
pages. TO EXIT NETWORK SETUP 1. When you have finished entering service settings, choose Exit Network Setup. 2. Choose Yes when prompted to save changes. 3. From the main Setup menu, choose another Setup or choose Exit Setup. Network Setup Port Setup Port Setup options You can enable Ethernet - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 64
problems, set this option to No. NOTE: If you use a PC with Windows XP or Windows 2000, printing over the parallel port may succeed but you may need to install and use a utility that fixes ECP mode. Without the fix, ECP mode on those platforms runs very slowly. Contact your authorized service support - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 65
can enable AppleTalk, TCP/IP, and IPX/SPX communication simultaneously. AppleTalk Setup Enable AppleTalk Yes/No [Yes] Select Yes if you have an an IP address, subnet mask, or gateway address for the Fiery X3e during Setup, you can allow the Fiery X3e to get these addresses automatically from a DHCP - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 66
44-12 Performing Setup from the Control Panel Network Setup Protocol Setup TCP/IP Setup TCP/IP Setup with Ethernet Ethernet Setup Enable TCP/ . If you select No, you proceed to the IP Address option, where you manually set the IP address. Select protocol DHCP/BOOTP [DHCP] This option appears only - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 67
44-13 Network Setup options IP Address [127.0.0.1] Enter the Fiery X3e IP address for Ethernet. This IP address, unlike an IP address set automatically, remains the same if - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 68
from the Control Panel Network Setup Protocol Setup DNS Setup DNS Setup DNS Setup Enable DNS Yes/No [No] Select Yes to allow the Fiery X3e to resolve a name to an IP address. This option must be enabled to use PrintMe services. Get DNS Automatically Yes/No [No] Select Yes to allow the Fiery X3e - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 69
than IPX/SPX, the frame type is automatically enabled and does not require setup, as follows: With this protocol And these printing services This frame type is automatically enabled AppleTalk TCP/IP with Ethernet PAP (Printer Access Protocol) LPD (Line Printer Daemon) Ethernet SNAP Ethernet II - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 70
To determine the frame types that were successfully bound, save your changes, exit Setup, restart the Fiery X3e, and print a Configuration page. The Configuration . If you answer No to this option, you can select frame types manually. You must choose at least one frame type to enable IPX/SPX protocols - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 71
44-17 Network Setup options Network Setup Service Setup LPD Setup Network Setup Service Setup PServer Setup Service Setup options PServer is a program in the Fiery X3e software that services the Novell print queues assigned to the Novell print servers set up for printing to the Fiery X3e. When you - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 72
from the Control Panel Network Setup Service Setup PServer Setup NDS Setup Before entering NDS settings, make sure the Fiery X3e is connected to the network and that you have configured an NDS directory tree with a Printer, Print Server, and one or more Print Queue objects for Fiery X3e jobs (see - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 73
44-19 Network Setup options Is user login needed to browse NDS tree? Yes/No [No] Select tree, as described in the following paragraphs. NDS Tree name Object list, ".." Browsing to find the User Login object begins with the NDS tree that you selected previously (with Select NDS Tree). Use the up and - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 74
44-20 Performing Setup from the Control Panel Enter Password Enter the login password for OK. (If no password is required, choose OK.) Server should look for print queues in: Entire NDS Tree/Specif. Subtree [Entire NDS Tree] By default, the Fiery X3e searches the entire NDS tree for Fiery X3e print - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 75
If you select Entire NDS Tree, choosing OK returns to PServer Setup. Proceed with Bindery Setup (see page 4-22), set the Polling Interval (see page 4-27), or choose Exit PServer Setup to return to the Service Setup menu. Browse to the root of the Print Queue Subtree. This message is displayed - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 76
22 Performing Setup from the Control Panel Network Setup Service Setup PServer Setup Bindery Setup options Bindery Setup Use Bindery Setup if the NetWare file server is running. If Guest Login is not supported, you need a valid user name and password. NOTE: The terms NetWare server, Novell server, - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 77
44-23 Network Setup options Network Setup Service Setup PServer Setup Bindery Setup Add File Server This option gives you two ways to add a Novell NetWare file server. Select File Server From List/Search by Name [From List] - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 78
44-24 Performing Setup from the Control Panel File Server Login administrator/supervisor/Enter Login Name [supervisor] This option appears only if a password is required for for printing to the Fiery X3e. When you have added all the IPX file servers for your site, choose Exit Bindery Setup. - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 79
44-25 Network Setup options Network Setup Service Setup PServer Setup Bindery Setup Network Setup Service Setup PServer Setup Bindery Setup View Server List Supported servers This option allows you to view the list of file servers currently connected to the Fiery X3e-that is, servers you have added - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 80
44-26 Performing Setup from the Control Panel Network Setup Service Setup PServer Setup Bindery Setup Network Setup Service Setup PServer Setup Bindery Setup Enter Your Print Server Password This option appears only if your NetWare print server is password-protected. Enter your print server - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 81
Setup options Network Setup Service Setup PServer Setup Network Setup Service Setup Windows Setup Polling Interval options Polling Interval Whether you use NDS or Bindery services, choose Polling Interval from the main PServer Setup , see the User Software Installation Guide. Windows printing - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 82
manual. To find out if a name server is available, contact your network administrator. Point and Print Drivers PS/PCL [PS] Select the type of driver to download when setting up a printer Server Setup (see page 4-4). Server Comments Server comments (optional) can contain information about the printer. - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 83
browser and a valid IP address or DNS host name are required for each user. For details on browser choice and workstation requirements, see the User Software Installation Guide. Network Setup Service Setup IPP Setup IPP Setup Enable IPP Yes/No [Yes] Select Yes to enable printing with the Internet - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 84
for downloading jobs to Port 9100. Only the print connections you have enabled in Printer Setup are available. E-mail Setup Enable E-mail Services Yes/ Enabling this option allows the service technician to remotely run diagnostics through e-mail. See your copier documentation for more information. - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 85
Network Setup options RD Incoming Server 127.0.0.1 This option appears only if you have selected Yes to Enable Remote Diagnostics. See your copier documentation to Enable Remote Diagnostics. See your copier documentation for more information. RD Admin User Name youremail This option appears only if - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 86
Setup address [email protected], the domain name is test.com. See your copier documentation for more information. Outgoing Server [127.0.0.1] Enter the IP address /IMAP [POP3] Choose the type of mail server. Fiery E-mail User Name Enter the user name of the e-mail account. This is typically the part of the - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 87
The administrator authorizes a unique e-mail address to remotely administer Fiery E-mail Services via e-mail. If an error occurs while you are executing a scan to e-mail, the e-mail service sends an error message to that administrator e-mail address. The administrator can authorize additional e-mail - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 88
from the Control Panel Network Setup Service Setup FTP Setup FTP Setup Enable FTP Services Yes/No [Yes] This option enables users to scan jobs from the Fiery X3e to an FTP site. Enable Proxy Setup No/Yes [No] Select Yes to enable the following proxy server setup options for security purposes when - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 89
44-35 Printer Setup options Network Setup Service Setup Proxy Server User Name Enter the user name for the proxy server. This option appears only if you have selected Yes to Enable Proxy Setup. Proxy Server User Password Enter the user password for the proxy server. This option appears only if you - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 90
basis. Only queues published in the Printer Setup are available to users. NOTE: To print to the Fiery X3e over the parallel port, you must publish a queue or publish the Direct connection. Publish Hold Queue Yes/No [Yes] Use this option to allow users to print (or download) jobs to the Hold queue - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 91
basis. However, users printing from UNIX or DOS command lines cannot override defaults from their applications. Therefore, you must set defaults in PostScript Setup. For information about these defaults, see the Printing Guide. TO ACCESS POSTSCRIPT SETUP OPTIONS 1. In the main Setup menu, choose PS - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 92
to cancel the print job entirely when a PostScript error is encountered. Leave this option at No unless you encounter printing problems. Allow Courier Substitution Yes/No [Yes] Specify whether to substitute Courier for fonts that are unavailable when you download files to the Fiery X3e, or when you - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 93
printer output. These defaults can be overridden by the user from within an application, but they determine how a job will be printed in the absence of other information. NOTE: PCL printing is supported for Windows computers only. Mac OS computers must use the PostScript driver. TO ACCESS PCL SETUP - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 94
-40 Performing Setup from the Control Panel Default Orientation Portrait/Landscape [Portrait] This option determines whether the text or image will be This option lets you choose the symbol set that best matches the needs of users printing to the Fiery X3e. Font Number 0-999 [0] The font number - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 95
44-41 Color Setup options Paper Size for System Pages US/Metric [US in United States, Metric elsewhere] Guide and Color Guide. NOTE: In addition to the defaults described in this section, additional settings are available to Mac OS and Windows users from the printer drivers. TO ACCESS COLOR SETUP - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 96
the United States, DIC in Japan, and Euroscale in Europe. Custom simulations are user defi Color Guide. CMYK Simulation Method Quick/Full (Source GCR)/Full (Output GCR) [Full (Output GCR)] Quick simulation assumes that the copier toners match the printer's inks, and all changes affect only one color - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 97
the best equivalents of PANTONE colors. With this option Off, PANTONE colors are printed using the CMYK values defined in the original applications. For more information, see the Color Guide. Save Changes Yes/No [Yes] Select Yes to activate any changes made in Color Setup; select No to return to - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 98
from the Control Panel PrintMe Setup options PrintMe allows users to access and print their e-mail messages, about PrintMe, go to www.printme.com. TO ACCESS PRINTME SETUP OPTIONS 1. In the main Setup menu, choose PrintMe Setup. 2. Enter the options appropriate to the printing requirements at - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 99
This displays the PrintMe activation code. If no activation code is available, PrintMe is not enabled. You must first enable PrintMe and follow the instructions on the previous page. Web Proxy Setup Specify proxy settings if your network uses a proxy server to access external web sites. Web Proxy - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 100
44-46 Performing Setup from the Control Panel Proxy Port Number Proxy Port Number 0-65535 [0] Enter the proxy port number assigned to PrintMe Services. In addition, some proxy servers require a user name and password for access. If the proxy server in your environment has such requirements, you must - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 101
jobs and color output, but are not required for printing. • Job Log Setup allows you to specify whether the Fiery X3e prints and clears its log of printed jobs automatically. • Change Password allows you to create or change an Administrator password on the Fiery X3e so that casual users cannot enter - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 102
date printed, and number of pages. Windows and Mac OS users can enter job-specific notes that appear in the Job Log. By default, the Job Log is not printed or cleared automatically. You can change these defaults in Job Log Setup. You can also print and clear the Job Log from the - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 103
Job Log. Regardless of page size, 55 jobs are listed on a page. The paper size used depends on the Default Paper Sizes setting in PS Setup. If the Default Paper Sizes setting is US, the Job Log is printed on Tabloid or Letter size paper, with Tabloid the default. Save Changes - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 104
- Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 105
Chapter 5: Setting up the Fiery X3e from a Windows Computer After you perform initial Setup (Server, Network, and Printer Setup) from the Control Panel, you can change most Setup options from a Windows computer. Accessing Setup In addition to using the Control Panel, you can set up the Fiery X3e - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 106
55-2 Setting up the Fiery X3e from a Windows Computer TO ACCESS SETUP FROM COMMAND WORKSTATION 1. Start Command WorkStation. 2. Log on as Administrator. 3. Choose Setup from the Server menu. Regardless of how you access Setup remotely, the following dialog box appears. NOTE: The interface of remote - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 107
55-3 General Setup options General Setup options You can specify Fiery X3e system settings that affect all users, such as the name of the one Fiery X3e, do not assign them the same name. Windows NT 4.0 does not support more than one computer with the same name in the same workgroup or domain. Date - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 108
jobs from the Fiery X3e hard disk. Choose Manually to delete scan jobs manually on a job-by-job basis. Click Delete Support-Enter names, phone numbers, and e-mail addresses of contact people at your organization who provide support for the Fiery X3e and the copier. In remote Setup, use the Support - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 109
Setup options Job Log Setup Auto Print Job Log Every 55 Jobs-Specify whether the Fiery X3e prints the Job Log after every 55 jobs. The Job Log lists the last 55 jobs processed on the Fiery X3e, with accounting information about each one, including user Job Log manually at any time with the job management - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 110
. You can view and specify the following network settings in Network Setup: • Adapters and ports-view currently configured network adapters and port TCP/IP • Print Services-including LPD printing (TCP/IP), NetWare printing (PServer), Windows print sharing (SMB), HTTP support (WWW), Internet Printing - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 111
55-7 Network Setup Adapters/Ports Ethernet (Port Setup) Enable Ethernet-Select to connect the Fiery X3e to an Ethernet network. Transmission Speed-Choose Auto Detect if your network environment is mixed, or choose the speed of the network to which the Fiery X3e is attached (10 Mbps or 100 Mbps). - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 112
55-8 Setting up the Fiery X3e from a Windows Computer Parallel Port (Port Setup) Enable Parallel Port-Specify whether you want to print through the parallel port. You can connect a single Windows computer to the parallel port and print - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 113
55-9 Network Setup Protocols You can change AppleTalk, IPX/SPX, and TCP/IP protocol settings for the Fiery X3e. Change these settings on the Protocol1 and Protocol2 tabs. - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 114
55-10 Setting up the Fiery X3e from a Windows Computer AppleTalk The current AppleTalk zone is displayed. - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 115
55-11 Network Setup IPX/SPX Use this option to specify IPX/SPX frame types. The Fiery X3e supports the following Ethernet frame types for IPX/SPX: Ethernet 802.2, Ethernet 802.3, Ethernet II, and Ethernet SNAP. You can also allow the Fiery X3e to select the frame type automatically. - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 116
obtains the IP addresses automatically. NOTE: If you specify the DHCP or BOOTP protocol, the Fiery X3e restarts when you save your changes and exit Setup. Allow the Fiery X3e to restart and return to Idle before printing a Configuration page or proceeding with any other operations. - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 117
55-13 Network Setup To set the subnet mask, enter one of the following values: 255.0.0.0 if cases, the required setting may be different from those listed. If your TCP/IP network has a gateway and users outside the gateway plan to print to the Fiery X3e using TCP/IP, enter the gateway address. NOTE: - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 118
Printing (TCP/IP)-enable or disable LPD print services. • NetWare Printing (PServer)-specify NDS and Bindery services (see page 5-16). • Windows Print Sharing (SMB)-enable or disable SMB print services. • HTTP Support (WWW)-enable or disable support for Fiery WebTools. • Port 9100-enable or disable - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 119
55-15 Network Setup LPD Printing Enable LPD Print Services-Select to enable or disable LPD printing services. Enable Web Services-Select to enable or disable web services. Enable FTP Services-Select to enable or disable FTP services. - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 120
Setting up the Fiery X3e from a Windows Computer NetWare Printing options Use this option to specify NDS and Bindery services. TO SPECIFY THE NDS TREE SETTING FROM REMOTE FIERY X3E SETUP 1. Select Enable NDS and click Change Trees. 2. In the NDS Configuration dialog box that appears, double-click an - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 121
55-17 Network Setup 3. In the Select User Login window, select Use Default User Information or enter your password, and click Next. 4. Navigate to the NDS container, select it, and click Next. If necessary, enter the password. - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 122
55-18 Setting up the Fiery X3e from a Windows Computer 5. Select Use Default Print Queue Root or navigate to the Print Queue Root and click Finish. - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 123
55-19 Network Setup 6. Click OK. The NDS Configuration dialog box appears, displaying information about the print server. - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 124
Use this option to specify Bindery services. TO ADD BINDERY CONNECTIONS FROM REMOTE FIERY X3E SETUP 1. Select Enable PServer mode from the Service1 tab. 2. Click Bindery Setup. 3. Select a file server from the Available Servers list. If the File Server User Name and Password dialog box appears, enter - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 125
55-21 Network Setup 4. Select a print server from the list and click Finish. If necessary, enter the appropriate password in the Print Server Password dialog box to log on - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 126
-22 Setting up the Fiery X3e from a Windows Computer TO REMOVE BINDERY CONNECTIONS FROM REMOTE FIERY X3E SETUP 1. Select Enable PServer mode from the Service1 tab. 2. Click Bindery Setup. The Novell Setup dialog box appears. 3. Make your selection in the Selected Servers list. 4. With the file server - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 127
55-23 Network Setup PServer Poll Interval Specify the polling interval (in seconds) for NetWare printing. - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 128
-24 Setting up the Fiery X3e from a Windows Computer Windows print sharing with Server Message Block (SMB) To set up the Windows printing service, text fields may include uppercase letters, numerals, spaces, and the following characters NOTE: Lowercase letters are not allowed, except in the Comment - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 129
-25 Network Setup Enable Windows Printing Service-Select to enable SMB (Server Message Block), the file and printer sharing protocol information on setting up a Windows client for Windows printing, see the User Software Installation Guide. NOTE: Windows (SMB) printing runs over TCP/IP, so you must - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 130
enabled IP Auto in Protocol Setup, and selected either DHCP manual. To find out if a name server is available, contact your network administrator. IP Address-Enter the IP address of the WINS name server. HTTP Connection Support (WWW) Enable Web Services-Select to make the WebTools available to users - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 131
Network Setup Port 9100 printing Enable Port 9100-Enables applications to open a TCP/IP socket to the Fiery X3e at Port 9100 to download a print job. Port 9100 Queue-Allows you to attach Port 9100 to any of the published Fiery X3e print connections. FTP Services Enable FTP Services-Allows users to - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 132
55-28 Setting up the Fiery X3e from a Windows Computer E-mail Service Setup E-mail Service Setup-Enabling e-mail services is required for all e-mail client services. Enable Print via E-mail-If selected, print jobs sent via e-mail are accepted. If this option is cleared, print jobs sent via e-mail - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 133
. Administrator E-mail Address-Enter the user name specified in Fiery X3e setup. The administrator authorizes a unique e-mail address to remotely administer e-mail services. If an error occurs while you are performing a scan to e-mail, E-mail Service sends an error message to the Administrator E-mail - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 134
X3e from a Windows Computer Printer Setup options From this dialog box, you can access the Printer Setup and Paper Setup tabs. NOTE: In the following illustrations, "Device name" represents the model of the copier connected to the Fiery X3e, which is 31C-M. Printer connections Specify whether to - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 135
55-31 Printer Setup options PS (PostScript) Setup The options in the PS Setup menu in local Setup are located on the Paper Setup tab in remote Setup. NOTE: In the following illustrations, "Device name" represents the model of the copier connected to the Fiery X3e, which is 31C-M. Convert Paper Sizes - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 136
choose Yes, each print job is followed by a page containing the name of the user who sent the job, the document name, the server name, the time the job jobs requiring fonts unavailable on the Fiery X3e hard disk generate a PostScript error and do not print. This setting does not apply to PDF files; - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 137
Guide. NOTE: Printing Groups is not supported with Windows 2000/XP. NOTE: To change the Group Name or Group Password settings for a job that a user has already sent from the printer driver group name in the Printing Groups Setup dialog box and click Modify. 3. Make the necessary changes. 4. Click OK. - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 138
and restarted the Fiery X3e for the first time, install the user software for printing on remote workstations, as described in the User Software Installation Guide. To confirm the network connection and your Setup, print a test job from a remote workstation. Printing the Configuration page The Con - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 139
gateway address, if required. 3. Enable Web Services. 4. In Fiery X3e Printer Setup, confirm that the Print Queue is supports the Java language and frames. Make sure Java is enabled. For more information on supported browsers and WebTools requirements, see the User Software Installation Guide - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 140
Network Setup>Port Setup > Ethernet Port Setup. 2. Set Enable TCP/IP for Ethernet to Yes in Network Setup> TCP/IP Ethernet Setup. 3. Set Enable Web Services to Yes in Network Setup >Network Service Setup>Web Services Setup. 4. Exit Network Setup, and choose OK to Save Changes. 5. Exit Printer Setup - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 141
66-3 Setting the WebLink destination Setting the WebLink destination You can change the pre-set WebLink destination; this function requires the Administrator password, if one has been set. TO CHANGE THE WEBLINK DESTINATION 1. Start your Internet browser. 2. Enter the IP address or the DNS name of - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 142
- Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 143
to allow user access to WebTools This manual This manual Release Notes Setting up the printing environment Setting printer defaults, including modes, imaging, paper size handling, error handling Printer Setup, pages 4-35,5-30 PS Setup, pages 4-37 and 5-31 Color Guide Printing Guide Setting up - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 144
Printing with CMYK simulations Printing color samples and swatch pages Installing color profiles Color Guide User Software Installation Guide Tips Deleting jobs, clearing queues page 7-9, also Job Management Guide Troubleshooting Fiery X3e Setup Appendix A Setting passwords You can set or - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 145
, see page 3-3. For information on controlling print jobs with the job management tools, see the Job Management Guide. NOTE: The Operator password can be set and changed only from Fiery WebSetup, local Setup, or Command WorkStation. TO CHANGE THE FIERY X3E PASSWORD 1. Scroll through the main - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 146
they allow, see page 3-3. By default, no passwords are set. If you do not specifically set passwords, all users will have access to important functions such as Setup (including setting passwords) and job control. We strongly recommend that you set at least an Administrator password to protect the - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 147
elds. If you forget the Administrator password, contact your authorized service representative to reinstall Fiery X3e system software. This clears the of Fiery FreeForm masters. To clear the Fiery X3e, scroll through the Setup menu and choose Clear Server. You are asked to confirm your selection. If - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 148
The E-mail Service feature allows an administrator to import a list of e-mail addresses to the Fiery X3e by sending e-mail messages to the Fiery X3e. NOTE: E-mail messages can be sent only from an administrator account. The Fiery X3e supports the following address books: • User-a generic address - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 149
name of address book For example: #AddAddressTo Print To clear an address book #ClearAddressBook name of address book For example: #ClearAddressBook User Administrator message field Fiery e-mail response subject field Fiery e-mail response message field name@domain or "display name" - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 150
e-mail services #DeleteAddressFrom name of address book For example: #DeleteAddressFrom User #Help troubleshooting e-mail syntax. Printing a Configuration page from the Control Panel The Configuration page lists all the settings in effect in the current Setup. After you have finished running Setup - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 151
obvious requirements of servicing and maintaining the copier and replenishing consumables, or connections to the demand for printing. Review the published connections by printing a Confi low-traffic times, the administrator or a user of the job management tools with Operator privileges can move - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 152
(in Printer Setup). To move or remove queued jobs, use the job management tools. When you free up disk space by removing inactive jobs, new jobs are spooled and printed more quickly. Shutting down, rebooting, and restarting the Fiery X3e Generally, you can leave the Fiery X3e and the copier running - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 153
the down arrow to scroll to Shut Down. 6. Select Shut Down System. 7. It is now safe to turn off the copier using the main power switch. NOTE: After turning off the copier, wait at least three seconds before turning it back on. TO REBOOT THE FIERY X3E 1. Press the Utility button on - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 154
to the Fiery X3e is temporarily interrupted and all currently processing jobs are aborted. TO RESTART THE FIERY X3E 1. Turn on the copier using the main copier power switch. 2. Press the Utility button on the Control Panel. 3. In the Touch Panel, press the Controller Detail button. 4. Press the Menu - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 155
are described in the Installation and Service Guide for service technicians. Contact your authorized service/support center if you see startup error messages on Command WorkStation or if the Fiery X3e does not reach the Idle state. Troubleshooting during Setup from the Control Panel The following - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 156
AA-2 Troubleshooting After this Setup screen Enable NDS (Network Setup>Service Setup>PServer Setup>NDS Setup) Select NDS Tree (Network Setup>Service Setup>PServer Setup> NDS Setup) Navigating NDS tree (Network Setup>Service Setup>PServer Setup> NDS Setup) Bindery Setup (Network Setup>Service Setup> - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 157
AA-3 Troubleshooting After this Setup screen Enter First Letters of Server Name (Network Setup>Service Setup>PServer Setup> Bindery Setup) View Server List, Edit Connection (Network Setup>Service Setup>PServer Setup> Bindery Setup) Add File Server (Network Setup>Service Setup>PServer Setup> Bindery - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 158
not possible, you are prompted to notify the Novell administrator, who will need to troubleshoot the network. Consult NetWare Administrator documentation for further explanation of Novell error codes. In Network Setup, when you configure the IPX (Novell) connection, the Fiery X3e queries the network - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 159
Troubleshooting For any Novell error, • You have the appropriate permissions and login information, including user name and password, if necessary. • The Fiery X3e to Print Server failed). Pressing the Menu button returns to the PServer Setup screen. 252 Unable to log in to server. Login does not - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 160
off ). Pressing the Menu button returns to the PServer Setup screen. Indicates other network errors when the Fiery X3e is already connected to a file server unexpected has happened and the user generally cannot recover without intervention of the network administrator. Error #197 indicates that you have - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 161
Troubleshooting Runtime error messages For error messages related to canceling jobs and printing, including the Disk Full message and alerts to load media, see the Job Management Guide. These messages are reported by the job management tools. You can turn on PostScript error Setup. • Remote printer - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 162
Troubleshooting See the following table for the appropriate name. In this location Server Setup Windows NT hosts file Windows NT setup name page 2-1 (TCP/IP host name) Name of printer on lpd host machine - print or hold rp supported over IPX/SPX. Utilities are not supported over IPX/SPX. - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 163
Troubleshooting Cannot connect to Fiery X3e with Fiery utilities If users cannot connect to the Fiery X3e, check the following: • Fiery X3e Setup problem connecting to the Fiery X3e, an error message is displayed. The problem as described in the User Software Installation Guide. For Windows9x/Me, the - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 164
- Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 165
to 7-2 installing the server 1-2 managing print jobs 7-1 password 7-2 Administrator E-mail Domain Name option, E-mail Setup 4-33 Administrator E-mail User Name option, E-mail Setup 4-33 Administrator password changing from Control Panel 7-2 changing from Windows computer 7-5 for setting the WebLink - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 166
Profile option 4-42 Color Mode option 4-38 Color Setup 4-41 Command WorkStation 11 problems connecting to server A-9 Comment option, Windows printing 4-28, 5-25 Configuration page determining IPX frame types bound 4-16 printing 5-34, 7-8 troubleshooting connection problems A-9 Configure button, Fiery - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 167
4-14 Domain or Workgroup option, Windows printing 4-29, 5-25 downloading fonts, Direct connection requirement 3-2 drivers, Point and Print 4-28 E Edit Connection, Bindery Setup 4-25 explained 4-22 E-mail Service Setup option 5-28 E-mail Setup 4-30 Enable AppleTalk option 4-11 Enable Auto IP Con - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 168
, Bindery 5-20 file types and parallel port setup 4-10, 5-8 font substitution 4-38, 5-32 frame types supported AppleTalk 4-15 IPX/SPX 4-15 IPX/SPX, connecting 4-22 NDS (Novell Directory Services) 2-11, 4-17, 5-14 NetWare client setup 2-12 NetWare server setup 2-9 network diagram 1-6 overview of - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 169
NDS Setup 4-18 NDS tree browsing 4-18, 4-19 browsing to print queue root 4-20 browsing to Print Server 4-20 browsing to User Login object 4-19 password 4-19 NETADMIN 2-10 NETBEUI 1-7 NetWare Bindery and NDS on the same network 4-17 Bindery Services 4-17 Directory Services 4-17, 5-14 error messages - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 170
Print Start Page option 4-5, 5-4 Print Start Page, printing 5-4 Print to PostScript Error option 4-38, 5-32 Printed queue 3-2, 4-6 printer connection failure A-7 not found A-7 not in Chooser A-7 Printer Agent, NDPS 2-13 Printer Setup from Control Panel 4-35 from Windows computer 5-30 part of initial - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 171
33 removing printing groups and passwords 5-34 problems, see troubleshooting protocols for assigning IP address automatically 4- Color Setup, Control Panel 4-43 Job Log Setup, Control Panel 4-46, 4-49 Network Setup, Control Panel 4-9, 4-35 PCL Setup 4-41 Printer Setup, Control Panel 4-36, 4-38 Setup - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 172
Setup, Network Setup, Printer Setup, PS Setup, Job Log Setup Setup from Control Panel accessing 4-2 administrative functions 4-47 Color Setup 4-41 error messages A-1 Job Log Setup 4-48 Network Setup 4-7 Port Setup 4-9 Printer Setup 4-35 Protocol Setup 4-11 to 4-15 Server Setup 4-4 Service Setup - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 173
printcap file A-8 printing to server 2-19 remote printer name A-8 setting up printing to server 2-18 tips Setup 4-25 explained 4-22 W warning display window breakage 4-2 Web Services Setup 2-6, 4-27, 5-14, 5-25 domain issues 3-8 selecting drivers for 4-28 setting domain or workgroup 4-29, 5-25 WINS - Kyocera KM-C2030 | Fiery X3e Configuration Guide for Ver 2.0 - Page 174
Fiery X3e
CONFIGURATION GUIDE