Kyocera KM-C2030 Fiery X3e Configuration Guide for Ver 2.0 - Page 66

TCP/IP Setup with Ethernet, Ethernet Setup, Network Setup, Protocol Setup, TCP/IP Setup

Get Kyocera KM-C2030 PDF manuals and user guides View all Kyocera KM-C2030 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

44-12 Performing Setup from the Control Panel Network Setup Protocol Setup TCP/IP Setup TCP/IP Setup with Ethernet Ethernet Setup Enable TCP/IP for Ethernet Yes/No [Yes] Select Yes if you have a TCP/IP network connected to the Fiery X3e over Ethernet cabling. NOTE: If you are using TCP/IP for printing from Windows computers, enabling TCP/IP here also enables you to use Fiery utilities from Windows computers using TCP/IP protocols. Enable Auto IP Configuration Yes/No [Yes] Select Yes to allow the Fiery X3e to obtain its Ethernet IP address by searching the network. Depending on your network and the protocol you select in the following option (DHCP or BOOTP), the IP address can change. Select No to assign the Fiery X3e a static IP address. If you select No, you proceed to the IP Address option, where you manually set the IP address. Select protocol DHCP/BOOTP [DHCP] This option appears only if you answered Yes to Enable Auto IP Configuration. Select the protocol over which the Fiery X3e should search for its IP address. Both DHCP and BOOTP allow the Fiery X3e to obtain the Ethernet IP address and Subnet Mask automatically. Depending on your network, the Fiery X3e might be assigned a different address after you restart the Fiery X3e. With the DHCP setting, the Fiery X3e can be assigned a different address even if it is not restarted. Make sure the network is already configured properly for the protocol you select. Get Gateway Address Automatically Yes/No [Yes] Use this option to assign the gateway address automatically for printing with TCP/IP.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
4
4-12
Performing Setup from the Control Panel
TCP/IP Setup with Ethernet
Enable Auto IP Configuration
Yes/No [Yes]
Select Yes to allow the Fiery X3e to obtain its Ethernet IP address by searching the
network. Depending on your network and the protocol you select in the following
option (DHCP or BOOTP), the IP address can change. Select No to assign the
Fiery X3e a static IP address. If you select No, you proceed to the IP Address option,
where you manually set the IP address.
Select protocol
DHCP/BOOTP [DHCP]
This option appears only if you answered Yes to Enable Auto IP Configuration. Select
the protocol over which the Fiery X3e should search for its IP address. Both DHCP
and BOOTP allow the Fiery X3e to obtain the Ethernet IP address and Subnet Mask
automatically.
Depending on your network, the Fiery X3e might be assigned a different address after
you restart the Fiery X3e. With the DHCP setting, the Fiery X3e can be assigned a
different address even if it is not restarted. Make sure the network is already configured
properly for the protocol you select.
Get Gateway Address Automatically
Yes/No [Yes]
Use this option to assign the gateway address automatically for printing with TCP/IP.
Network Setup
Protocol Setup
TCP/IP Setup
Ethernet Setup
Enable TCP/IP for Ethernet
Yes/No [Yes]
Select Yes if you have a TCP/IP network connected to the Fiery X3e over Ethernet
cabling.
N
OTE
:
If you are using TCP/IP for printing from Windows computers, enabling
TCP/IP here also enables you to use Fiery utilities from Windows computers using
TCP/IP protocols.