Kyocera KM-C2030 Fiery X3e Configuration Guide for Ver 2.0 - Page 52

Network server setup requirements, Ensuring the copier connection

Get Kyocera KM-C2030 PDF manuals and user guides View all Kyocera KM-C2030 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

33-8 Preparing for Fiery X3e Setup The first time you perform Setup, you must use the Fiery X3e Control Panel. Configure, at a minimum, Server Setup, Network Setup, and Printer Setup, in that sequence. After the initial Setup, you can change Setup options from the Control Panel (page 4-2) or Command WorkStation. Most Setup options can be set using any of these methods. If you do not configure the remaining Setups, the Fiery X3e uses default settings. You need to make settings appropriate for the printing environment at your site. Network server setup requirements For Novell, and Windows NT 4.0/2000 (using TCP/IP) networks, you must configure the network servers for printing to the Fiery X3e before you configure Fiery X3e network settings in Setup. For chapter references to information about network server Setup, see the diagrams in Chapter 1. To configure network settings in Setup, you must have a live network connection, so the Fiery X3e can query the network for zones, servers, and server-based queues. Whenever the configuration of the Fiery X3e, the copier, or the network itself changes at your site, you can alter individual settings to correspond to the changed environment. Changing network or port settings may require that you make changes to other Setup options, as well. NOTE: You must configure the Fiery X3e with the correct Windows NT/2000 domain name. This is especially important for Windows printing, also known as SMB printing. NOTE: The Fiery X3e does not support the Windows 2000 Active Directory Service. When you use the Fiery X3e in a Windows 2000 server environment, assign the Fiery X3e to a Domain or Workgroup. Ensuring the copier connection Complete the following steps before you configure the Fiery X3e and the workstations that will print to the Fiery X3e. A service technician will have performed some initial installation.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
3
3-8
Preparing for Fiery X3e Setup
The first time you perform Setup, you must use the Fiery X3e Control Panel.
Configure, at a minimum, Server Setup, Network Setup, and Printer Setup, in that
sequence. After the initial Setup, you can change Setup options from the Control Panel
(
page 4-2
) or Command WorkStation. Most Setup options can be set using any of
these methods.
If you do not configure the remaining Setups, the Fiery X3e uses default settings. You
need to make settings appropriate for the printing environment at your site.
Network server setup requirements
For Novell, and Windows NT 4.0/2000 (using TCP/IP) networks, you must configure
the network servers for printing to the Fiery X3e
before
you configure Fiery X3e
network settings in Setup. For chapter references to information about network server
Setup, see the diagrams in
Chapter 1
.
To configure network settings in Setup, you must have a live network connection, so
the Fiery X3e can query the network for zones, servers, and server-based queues.
Whenever the configuration of the Fiery X3e, the copier, or the network itself changes
at your site, you can alter individual settings to correspond to the changed
environment. Changing network or port settings may require that you make changes
to other Setup options, as well.
N
OTE
:
You must configure the Fiery X3e with the correct Windows NT/2000
domain name. This is especially important for Windows printing, also known as
SMB printing.
N
OTE
:
The Fiery X3e does not support the Windows 2000 Active Directory Service.
When you use the Fiery X3e in a Windows 2000 server environment, assign the
Fiery X3e to a Domain or Workgroup.
Ensuring the copier connection
Complete the following steps
before
you configure the Fiery X3e and the workstations
that will print to the Fiery X3e. A service technician will have performed some initial
installation.