Kyocera KM-C2030 Fiery X3e Configuration Guide for Ver 2.0 - Page 64

Parallel Port Setup options, Network Setup, Port Setup

Get Kyocera KM-C2030 PDF manuals and user guides View all Kyocera KM-C2030 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

44-10 Performing Setup from the Control Panel Network Setup Port Setup Parallel Port Setup options You must enable the parallel port in order to enter the Parallel Port Setup options and print to the parallel port. Parallel Port Setup Enable Parallel Port Yes/No [No] Select Yes if you want to print through the parallel port. You can connect a single Windows computer to the parallel port and print directly to the Fiery X3e. Port Timeout in Seconds 5-60 [5] This option appears only if Enable Parallel Port is set to Yes. Your setting determines how long (in seconds) the Fiery X3e waits without receiving data from the parallel port before deciding that the current job is complete. Until the timeout, the Fiery X3e cannot receive new jobs through the parallel port, but it can continue to receive network print jobs. Ignore EOF Character Yes/No [Yes] This option appears only if Enable Parallel Port is set to Yes. This option specifies that the Fiery X3e should ignore end-of-file (EOF) messages in a file. This option must be set to Yes to print PostScript files in binary format (not ASCII); under normal circumstances, it should be set to No. When this option is set to Yes, the Fiery X3e uses the parallel port timeout value to determine when the end of the file has been reached. If you experience printing problems, set this option to No. NOTE: If you use a PC with Windows XP or Windows 2000, printing over the parallel port may succeed but you may need to install and use a utility that fixes ECP mode. Without the fix, ECP mode on those platforms runs very slowly. Contact your authorized service support center for more information.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
4
4-10
Performing Setup from the Control Panel
Parallel Port Setup options
You must enable the parallel port in order to enter the Parallel Port Setup options and
print to the parallel port.
Port Timeout in Seconds
5–60 [5]
This option appears only if Enable Parallel Port is set to Yes. Your setting determines
how long (in seconds) the Fiery X3e waits without receiving data from the parallel port
before deciding that the current job is complete. Until the timeout, the Fiery X3e
cannot receive new jobs through the parallel port, but it can continue to receive
network print jobs.
Ignore EOF Character
Yes/No [Yes]
This option appears only if Enable Parallel Port is set to Yes. This option specifies that
the Fiery X3e should ignore end-of-file (EOF) messages in a file. This option must be
set to Yes to print PostScript files in binary format (not ASCII); under normal
circumstances, it should be set to No. When this option is set to Yes, the Fiery X3e uses
the parallel port timeout value to determine when the end of the file has been reached.
If you experience printing problems, set this option to No.
N
OTE
:
If you use a PC with Windows XP or Windows 2000, printing over the parallel
port may succeed but you may need to install and use a utility that fixes ECP mode.
Without the fix, ECP mode on those platforms runs very slowly. Contact your
authorized service support center for more information.
Network Setup
Port Setup
Parallel Port Setup
Enable Parallel Port
Yes/No [No]
Select Yes if you want to print through the parallel port. You can connect a single
Windows computer to the parallel port and print directly to the Fiery X3e.