Kyocera KM-C2030 Fiery X3e Configuration Guide for Ver 2.0 - Page 45

Preparing for FieryX3e Setup, Levels of access and control, FieryX3e print connections

Get Kyocera KM-C2030 PDF manuals and user guides View all Kyocera KM-C2030 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

33-1 Levels of access and control Chapter 3: Preparing for Fiery X3e Setup To prepare for printing at your site, you must do some initial Fiery X3e configuration, or Setup, to specify the network environment and the kind of printing you will do. Before you perform Setup, you must decide the levels of access you will implement for your site. Administrators and operators must also understand how Fiery X3e system software is structured in order to configure and use the Fiery X3e system correctly. Levels of access and control When you configure the Fiery X3e during Setup, you (as system administrator) implement a particular level of control by enabling or not enabling print connections, passwords, and access to WebTools. The level of control you implement can range from minimum to moderate to maximum-or none at all. • Minimum control might be appropriate for a small site where anyone on the local network can control all printing and Fiery X3e functions. Although there may be an administrator or operator charged with certain duties, all users have equal access to the system and job management tools. • Maximum control might be appropriate for a high-volume printing environment where an administrator or operator controls the job flow and all printing; jobs sent by users are spooled (stored) to the Fiery X3e disk until the operator decides it is time to print them. In addition, only the administrator and operator have access to job management tools. This is the recommended level of control. NOTE: The term "job management tools" is used in this manual to refer to Command WorkStation, Fiery Spooler™, and Fiery WebSpooler™. Fiery X3e print connections The Fiery X3e supports three print connections: Hold queue, Print queue, and Direct connection. These print connections can be enabled, or "published," to users on the network when you configure Printer Setup. All published connections are constantly checked for the presence of jobs. The Print queue and Direct connection give remote users more direct access to the Fiery X3e than the Hold queue. Therefore, do not publish the Print queue and the Direct connection in environments where maximum control is desired.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
3
3-1
Levels of access and control
To prepare for printing at your site, you must do some initial Fiery X3e configuration,
or Setup, to specify the network environment and the kind of printing you will do.
Before you perform Setup, you must decide the levels of access you will implement for
your site. Administrators and operators must also understand how Fiery X3e system
software is structured in order to configure and use the Fiery X3e system correctly.
Levels of access and control
When you configure the Fiery X3e during Setup, you (as system administrator)
implement a particular level of control by enabling or not enabling print connections,
passwords, and access to WebTools. The level of control you implement can range
from minimum to moderate to maximum—or none at all.
•
Minimum control might be appropriate for a small site where anyone on the local
network can control all printing and Fiery X3e functions. Although there may be an
administrator or operator charged with certain duties, all users have equal access to
the system and job management tools.
•
Maximum control might be appropriate for a high-volume printing environment
where an administrator or operator controls the job flow and all printing; jobs sent
by users are spooled (stored) to the Fiery X3e disk until the operator decides it is
time to print them. In addition, only the administrator and operator have access to
job management tools. This is the recommended level of control.
N
OTE
:
The term “job management tools” is used in this manual to refer to
Command WorkStation, Fiery Spooler
™
, and Fiery WebSpooler
™
.
Fiery X3e print connections
The Fiery X3e supports three print connections: Hold queue, Print queue, and Direct
connection. These print connections can be enabled, or “published,” to users on the
network when you configure Printer Setup. All published connections are constantly
checked for the presence of jobs. The Print queue and Direct connection give remote
users more direct access to the Fiery X3e than the Hold queue. Therefore, do not
publish the Print queue and the Direct connection in environments where maximum
control is desired.
Chapter 3:
Preparing for
Fiery X3e Setup