Kyocera KM-C2030 Fiery X3e Configuration Guide for Ver 2.0 - Page 65

Protocol Setup options, TCP/IP Setup options, AppleTalk Setup

Get Kyocera KM-C2030 PDF manuals and user guides View all Kyocera KM-C2030 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

44-11 Network Setup options Network Setup Protocol Setup Protocol Setup options To configure the Fiery X3e, choose each protocol and enter the settings for that protocol. You can enable AppleTalk, TCP/IP, and IPX/SPX communication simultaneously. AppleTalk Setup Enable AppleTalk Yes/No [Yes] Select Yes if you have an AppleTalk network connected to the Fiery X3e. This setting enables the Fiery X3e to communicate over AppleTalk networks. AppleTalk Zone List of zones The Fiery X3e searches the network for AppleTalk zones in your network segment. Scroll through the list to select the AppleTalk zone in which you want the Fiery X3e to appear. If your segment has only one zone, the Fiery X3e is assigned to that zone automatically. The message "No AppleTalk zone found" may mean your network has no zones, or the network cable is not connected (see Appendix A). Choose OK to dismiss the message. TCP/IP Setup options To configure the Fiery X3e for TCP/IP, choose TCP/IP Setup. Choose Ethernet Setup and enter the appropriate settings. Choose each network type you use (Ethernet) and enter the appropriate settings. When you set an IP address, subnet mask, or gateway address for the Fiery X3e during Setup, you can allow the Fiery X3e to get these addresses automatically from a DHCP or BOOTP server. First, turn on or restart the Fiery X3e and allow it to reach Idle. Make sure the DHCP or BOOTP server is running, and then perform Fiery X3e Setup.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
4
4-11
Network Setup options
Protocol Setup options
AppleTalk Zone
List of zones
The Fiery X3e searches the network for AppleTalk zones in your network segment.
Scroll through the list to select the AppleTalk zone in which you want the Fiery X3e to
appear. If your segment has only one zone, the Fiery X3e is assigned to that zone
automatically.
The message “No AppleTalk zone found” may mean your network has no zones, or the
network cable is not connected (see
Appendix A
). Choose OK to dismiss the message.
TCP/IP Setup options
When you set an IP address, subnet mask, or gateway address for the Fiery X3e during
Setup, you can allow the Fiery X3e to get these addresses automatically from a DHCP
or BOOTP server. First, turn on or restart the Fiery X3e and allow it to reach Idle.
Make sure the DHCP or BOOTP server is running, and then perform Fiery X3e
Setup.
To configure the Fiery X3e, choose each protocol and enter the settings for that
protocol. You can enable AppleTalk, TCP/IP, and IPX/SPX communication
simultaneously.
Network Setup
Protocol Setup
AppleTalk Setup
Enable AppleTalk
Yes/No [Yes]
Select Yes if you have an AppleTalk network connected to the Fiery X3e. This
setting enables the Fiery X3e to communicate over AppleTalk networks.
To configure the Fiery X3e for TCP/IP, choose TCP/IP Setup.
Choose Ethernet Setup and enter the appropriate settings. Choose each network
type you use (Ethernet) and enter the appropriate settings.