Panasonic 26PEK2U6 26PEK2U6 Service Manual - Page 127

SELECTING THE INSTALLATION SITE, 1. Indoor Unit, AVOID, Ceiling Type T1, Low Silhouette Ducted Type F1

Get Panasonic 26PEK2U6 PDF manuals and user guides View all Panasonic 26PEK2U6 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 127 highlights

Indoor Unit 5. SELECTING THE INSTALLATION SITE 5-1. Indoor Unit AVOID: areas where leakage of flammable gas may be expected. places where large amounts of oil mist exist. direct sunlight. locations near inverter lamps which may affect the performance of the unit. locations near heat sources which may affect the performance of the unit. locations where external air may enter the room directly. This may cause "sweating" on the air discharge ports, causing them to spray or drip. locations where the remote controller will be splashed with water or affected by dampness or humidity. installing the remote controller behind curtains or furniture. locations where the receiver in the indoor unit is exposed to the inverter lamp light. Faulty operation of the unit occurs. locations where high-frequency emissions are generated. 1. Specifications Ceiling (Type T1) Ceiling Air discharge Ceiling Wall Min. 10 inch Min. 10 inch Front view NOTE The rear of the indoor unit can be installed flush against the wall. Air intake Min. 2 ft. Side view Low Silhouette Ducted (Type F1) 4-Way Cassette (Type U1) 10 in. 10 in. 3 ft. 3 ft. 10 in. 3 ft. 3 ft. 3 ft. 1 Min.8 ft. Shows Low Silhouette Ducted Type only DO: select an appropriate position from which every corner of the room can be uniformly cooled. select a location where the ceiling is strong enough to support the weight of the unit. select a location where tubing and drain pipe have the shortest run to the outdoor unit. allow room for operation and maintenance as well as unrestricted air flow around the unit. install the unit within the maximum elevation difference above or below the outdoor unit and within a total tubing length (L) from the outdoor unit as detailed in the installation instructions packed with the outdoor unit. allow room for mounting the remote controller about 3 ft. off the floor, in an area that is not in direct sunlight nor in the flow of cool air from the indoor unit. If the indoor unit is installed on the ceiling where the temperature or humidity inside is high (over 86°F(30°C) /RH: 70%), add insulating material to the surface of the unit to avoid dew condensation. NOTE Air delivery will be degraded if the distance from the floor to the ceiling is greater than 10 ft. 9-27/32" (250 mm) Type F2 25-19/32" (650 mm) Wall Mounted (Type K1) Min. 6 inch Min. 6 inch Min. 12 inch Wall Mounted (Type K2) The air inlet and outlet of the indoor unit must be free of any obstructions to allow air to spread throughout the room. 1. The indoor unit must be within a maintenancesoace. min. 2" (5 cm) min. 3" (7.5 cm) min. 2" (5 cm) Front View 1-119

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
  • 291
  • 292
  • 293
  • 294
  • 295
  • 296
  • 297
1-119
1. Specifications
5. SELECTING THE INSTALLATION SITE
5-1. Indoor Unit
AVOID:
areas where leakage of flammable gas may be
expected.
places where large amounts of oil mist exist.
direct sunlight.
locations near inverter lamps which may affect the
performance of the unit.
locations near heat sources which may affect the
performance of the unit.
locations where external air may enter the room
directly. This may cause “sweating” on the air dis-
charge ports, causing them to spray or drip.
locations where the remote controller will be splashed
with water or affected by dampness or humidity.
installing the remote controller behind curtains or
furniture.
locations where the receiver in the indoor unit is
exposed to the inverter lamp light. Faulty operation
of the unit occurs.
DO:
select an appropriate position from which every
corner of the room can be uniformly cooled.
select a location where the ceiling is strong enough
to support the weight of the unit.
select a location where tubing and drain pipe have
the shortest run to the outdoor unit.
allow room for operation and maintenance as well as
unrestricted air flow around the unit.
If the indoor unit is installed on the ceiling where the
temperature or humidity inside is high (over 86°F(30°C)
/RH: 70%), add insulating material to the surface of the
unit to avoid dew condensation.
install the unit within the maximum elevation
difference above or below the outdoor unit and within
a total tubing length (L) from the outdoor unit as
detailed in the installation instructions packed with
the outdoor unit.
allow room for mounting the remote controller about
3 ft. off the floor, in an area that is not in direct
sunlight nor in the flow of cool air from the indoor
unit.
NOTE
Air delivery will be degraded if the distance from the
floor to the ceiling is greater than 10 ft.
Indoor Unit
locations where high-frequency emissions are
generated.
Ceiling (Type T1)
The rear of the indoor unit can be
installed flush against the wall.
Min. 2 ft.
Air intake
Min. 10 inch
Ceiling
Wall
NOTE
Min. 10 inch
Side view
Front view
Type F2
Ceiling
Wall Mounted (Type K1)
Min.
6 inch
Min.
12 inch
Min.
6 inch
Low Silhouette Ducted (Type F1)
4-Way Cassette (Type U1)
10 in.
10 in.
10 in.
3 ft.
3 ft.
3 ft.
3 ft.
3 ft.
Min.8 ft.
Shows Low Silhouette Ducted Type only
Air
discharge
9-27/32”
(250 mm)
25-19/32”
(650 mm)
Wall Mounted (Type K2)
The air inlet and outlet of the indoor unit must be free of any
obstructions to allow air to spread throughout the room.
1. The
indoor unit must be within a maintenance
soace.
Front View
min. 3" (7.5 cm)
min.
2"
(5
cm)
min.
2"
(5
cm)
1