Adaptec 1966600 User Guide - Page 113

Replacing the SAF-TE Controller Card, Problems with the DuraStor 312R Storage, Enclosure, Powering Off

Get Adaptec 1966600 - DuraStor 7220SS Hard Drive Array PDF manuals and user guides
UPC - 760884139202
View all Adaptec 1966600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 113 highlights

DuraStor 6220SS/7220SS Installation and User's Guide Replacing the SAF-TE Controller Card The SAF-TE controller has SCSI ID 15. If your storage management software tool is not recognizing that SCSI ID, the SAF-TE controller card may have failed. See Problems with the DuraStor 312R Storage Enclosure on page 6-2 for other indications that the SAF-TE controller card has failed. A failed SAF-TE controller card should be replaced immediately. Warning: The SAF-TE controller card is not hot-swappable. You must power off the storage enclosure to replace this card. Note: Make a note of the switch settings on the SAF-TE controller card before you remove it from the storage enclosure. 1 Power off the DuraStor 312R. See Powering Off on page 3-54. 2 Loosen the two screws that secure the SAF-TE controller card to the storage enclosure. 3 Grasp the screws and gently pull the SAF-TE controller card from the storage enclosure. 4 Align the replacement card with the rail guides of the open bay and push gently but firmly until the card seats completely. See Figure 5-10. 5 Tighten the screws. Do not overtighten. 6 Set the switch settings. Refer to the note you made before step 1. 5-14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
5-14
DuraStor 6220SS/7220SS Installation and User’s Guide
Replacing the SAF-TE Controller Card
The SAF-TE controller has SCSI ID 15. If your storage management
software tool is not recognizing that SCSI ID, the SAF-TE controller
card may have failed. See
Problems with the DuraStor 312R Storage
Enclosure
on page 6-2
for other indications that the SAF-TE
controller card has failed.
A failed SAF-TE controller card should be replaced immediately.
Warning:
The SAF-TE controller card is
not
hot-swappable.
You must
power off
the storage enclosure to replace this
card.
Note:
Make a note of the switch settings on the SAF-TE
controller card before you remove it from the storage
enclosure.
1
Power off the DuraStor 312R. See
Powering Off
on page 3-54
.
2
Loosen the two screws that secure the SAF-TE controller card to
the storage enclosure.
3
Grasp the screws and gently pull the SAF-TE controller card
from the storage enclosure.
4
Align the replacement card with the rail guides of the open bay
and push gently but firmly until the card seats completely. See
Figure 5-10
.
5
Tighten the screws.
Do not
overtighten.
6
Set the switch settings. Refer to the note you made before step 1.