Home » Adaptec Manuals » Hard Drive Cases » Adaptec 1966600 » Manual Viewer

Adaptec 1966600 User Guide - Page 47

Connecting to Two Storage Enclosures (13–24-Drive Configuration), DuraStor SCSI RAID Appliance

UPC - 760884139202

View all Adaptec 1966600 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Installing the DuraStor Storage Subsystem 3 Go to Connecting the SCSI RAID Appliance to the Host System on page 3-17, which describes how to set your operating mode. DuraStor SCSI RAID Appliance Disk CH 2 Disk CH1 HOST 1 IN (CH 3) HOST 2 IN (CH 0) HOST 1 OUT HOST 2 OUT Disk CH 2 Disk CH 1 Serial B Ext Serial A Int DuraStor 312R SCSI Data Cable SCSI Data Cable 1 2 3 4 5 6 78 Disk I/O Channel 2 Channel 1 (Output) (Input) Figure 3-11 Dual-Bus 2-12-Drive Cabling Diagram Connecting to Two Storage Enclosures (13-24-Drive Configuration) 1 Establish the drive configuration by setting the SAF-TE switches to reflect the settings shown in Figure 3-12. SAF-TE ID = 15 RAID Controllers = 6 & 7 DAA S SSDR B 0 1 0 1 2 LM 123 4 5678 UP (1) DOWN (0) Slot 1 ID 1 Slot 2 ID 3 Slot 3 ID 5 Single-bus Mode Slot 4 ID 2 Slot 5 ID 4 Slot 6 ID 0 Slot 7 ID 9 Slot 8 ID 11 Slot 9 ID 13 Slot 10 ID 10 Slot 11 ID 12 Slot 12 ID 14 Switch Settings Drive IDs of the Drive Slots (Drive Channel Side) Figure 3-12 Single-bus 13-24-drive Switch Settings 3-13

Section	Page
DuraStor6220SS/7220SS	2
Installation and User’s Guide	2
1	8
Introduction	8
About This Guide	8
Installation Overview	9
Storage Management Software Tools	9
Adaptec Storage Manager Pro	9
Adaptec Disk Array Administrator	10
The Operator Control Panel	10
2	11
About the DuraStor Storage Subsystem	11
About the DuraStor RAID Appliances	11
Front Bezel	13
Operator Control Panel (OCP)	14
Controller Canister	14
Power System	15
Cooling Fan Module	16
SCSI RAID Appliance I/O Connectivity Panel	17
Fibre Channel-to-SCSI RAID Appliance I/O Connectivity Panel	20
Optical SFP Transceiver	21
About the DuraStor312R Storage Enclosure	24
Front Bezel	25
Disk Drives	26
Power Supply Units	27
Cooling Fan Module	28
Disk I/O Card	29
SAF-TE Controller Card	30
Drive ID Settings	31
Spin-up Settings	33
3	35
Installing the DuraStor Storage Subsystem	35
Storage Subsystem Installation Overview	36
1. Setting Up the DuraStor RAID Appliance	36
2. Setting Up the DuraStor312R Storage Enclosure	36
3. Completing the DuraStor Storage Subsystem Setup	36
4. Installing Your Storage Management Tool	36
Setting Up the DuraStor RAID Appliance	37
Removing the Front Bezel	37
Mounting the RAID Appliance on the Rack	38
Replacing the Front Bezel	40
Connecting the Power Cords	40
Setting Up the DuraStor312R Storage Enclosure	40
Removing the Front Bezel	41
Mounting the Storage Enclosure on the Rack	42
Attaching a Disk Drive to a Drive Carrier	44
Installing Disk Drives	44
Replacing the Front Bezel	45
Connecting the Power Cords	45
Completing the Connections for the DuraStor6220SS	45
Connecting the SCSI RAID Appliance to the DuraStor312R	46
Connecting to One Storage Enclosure (2–12-Drive Configuration)	46
Connecting to Two Storage Enclosures (13–24-Drive Configuration)	47
Connecting to Three Storage Enclosures (25–36-Drive Configuration)	49
Connecting the SCSI RAID Appliance to the Host System	51
Stand-Alone Single-Port Mode	52
Stand-Alone Dual Port Mode	53
Active-Active Single Port Mode	54
Active-Passive Dual-Port Mode	55
Changing Your Drive Configuration	56
Changing Your Operating Mode	56
Setting the Host System HBA to Multiple-LUN Support	56
Completing the Connections for the DuraStor7220SS	57
Connecting the Fibre Channel-to-SCSI RAID Appliance to the DuraStor312R	57
Connecting to One Storage Enclosure (2–12-Drive Configuration)	58
Connecting to Two Storage Enclosures (13–24-Drive Configuration)	59
Connecting to Three Storage Enclosures (25–36-Drive Configuration)	60
Connecting to Four Storage Enclosures (37–48-Drive Configuration)	62
Connecting the Fibre Channel-to-SCSI RAID Appliance to the Host System	63
Important Information About SAN Environments	65
Topology Setup	67
Stand-Alone Dual-Port Topology	68
Active-Active Dual-Port Topology	68
Active-Active Single-Port Topology	69
About Stand-Alone Mode	69
About Active-Active Mode	70
Stand-Alone Dual-Port (Hubs Disabled)	72
Stand-Alone Dual-Port, Hubs Enabled	73
Active-Active Dual-Port, Hubs Disabled	74
Active-Active Dual-Port, Hubs Enabled	76
Active-Active Single-Port, Hubs Disabled	77
Active-Active Single-Port, Hubs Enabled	78
SAN Solution Strategies	80
Active-Active Dual-Port Mode	80
Active-Active Single-Port Mode	84
SAN Configuration Not Supported	87
Turning On the Power	88
Powering On	88
Powering Off	88
Accessing Your Storage Management Tool	88
Installing Storage Manager Pro	89
Accessing Disk Array Administrator	90
4	93
Monitoring the DuraStor Storage Subsystem	93
Monitoring the DuraStor RAID Appliance	94
Front Bezel LEDs	94
Audible Alarm	95
The Operator Control Panel	96
Monitoring the DuraStor312R Storage Enclosure	96
Status LEDs	97
Drive LEDs	97
Audible Alarm	99
5	100
Maintaining the DuraStor Storage Subsystem	100
Maintaining the DuraStor RAID Appliance	100
Replacing a RAID Controller	101
Replacing a Down Controller When in Active-Active Mode	102
Replacing the Cooling Fan Module	103
Replacing a Power Supply Unit	104
Replacing the DuraStor RAID Appliance Chassis	105
Maintaining the DuraStor312R Storage Enclosure	106
Replacing a Disk Drive	107
Replacing the Cooling Fan Module	109
Replacing a Power Supply Unit	110
Replacing the Disk I/O Card	112
Replacing the SAF-TE Controller Card	113
Replacing the DuraStor312R Chassis	114
Removing the Defective Enclosure	114
Installing the New Storage Enclosure	115
6	117
Troubleshooting	117
Problems with the DuraStor RAID Appliance	117
Problems with the DuraStor312R Storage Enclosure	118
A	119
Port Information	119
B	122
The Operator Control Panel of the DuraStor RAID Appliance	122
Glossary	124