Adaptec 1966600 User Guide - Page 74

Active-Active Dual-Port, Hubs Disabled, Configuration, Option Configuration, Operating Mode

Get Adaptec 1966600 - DuraStor 7220SS Hard Drive Array PDF manuals and user guides
UPC - 760884139202
View all Adaptec 1966600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

DuraStor 6220SS/7220SS Installation and User's Guide FC HBA 1 FC HBA 2 (soft ID) (soft ID) Host Computer DuraStor FC RAID Appliance Fibre Channel Data Cable P3 Fibre Channel Data Cable P4 Disk CH 3 Disk CH 2 Disk CH 0 Disk CH 1 P-2 P-1 Serial B P-3 P-4 Ext Serial A Int Figure 3-35 Stand-Alone Dual-Port Cabling Diagram After powering up all the system(s), you need to set the operating mode. By default, the controller's operating mode is set to activeactive single-port and the internal hub is set to Enabled. This topology is for stand-alone dual-port and will need to be changed. 1 Access the Controller menu from the OCP and select the appropriate controller (Controller 1 or Controller 2). 2 From the System menu, select Configuration, then select Option Configuration. 3 From the Option Configuration menu, select Operating Mode, select StandAlone Dual Port, then press Enter to set this selection. 4 Press Esc to return to the previous menus. Active-Active Dual-Port, Hubs Disabled The following diagram illustrates the logical connection of the active-active dual-port topology with hubs disabled. Note: All ports are independent and active. 3-40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
3-40
DuraStor 6220SS/7220SS Installation and User’s Guide
Figure 3-35
Stand-Alone Dual-Port Cabling Diagram
After powering up all the system(s), you need to set the operating
mode. By default, the controller’s operating mode is set to active-
active single-port and the internal hub is set to
Enabled
. This
topology is for stand-alone dual-port and will need to be changed.
1
Access the Controller menu from the OCP and select the
appropriate controller (Controller 1 or Controller 2).
2
From the System menu, select
Configuration
, then select
Option Configuration
.
3
From the Option Configuration menu, select
Operating Mode
,
select
StandAlone Dual Port
, then press
Enter
to set this
selection.
4
Press
Esc
to return to the previous menus.
Active-Active Dual-Port, Hubs Disabled
The following diagram illustrates the logical connection of the
active-active dual-port topology with hubs disabled.
Note:
All ports are independent and active.
Host Computer
FC HBA 1
(soft ID)
P3
P4
FC HBA 2
(soft ID)
Fibre Channel
Data Cable
Fibre Channel
Data Cable
DuraStor FC RAID Appliance
P-2
P-1
P-3
P-4
Disk CH 2
Disk CH 1
Disk CH 3
Disk CH 0
Serial A
Serial B
Ext
Int