Adaptec 1966600 User Guide - Page 90

Accessing Disk Array Administrator, Caution, Warning

Get Adaptec 1966600 - DuraStor 7220SS Hard Drive Array PDF manuals and user guides
UPC - 760884139202
View all Adaptec 1966600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

DuraStor 6220SS/7220SS Installation and User's Guide 4 Click OK. The Storage Manager Pro Introduction window appears. 5 Follow the on-screen instructions to complete the installation. 6 When the installation is complete, click Done. The Set Administrator Password window appears. 7 Type a new password, re-enter it to verify it, then click OK. Do not click OK without changing the password. ! Caution: You must supply the password immediately. If you do not supply the password, you will be unable to log in after the next reboot, and will have to uninstall and reinstall Storage Manager Pro. The installation is complete. You can now perform all of the functions described in the Adaptec Storage Manager Pro User's Guide. Warning: We strongly recommend that you regularly and consistently back up your data so that it may be recovered in the event of a failure that's not protected by a faulttolerant array. Accessing Disk Array Administrator Disk Array Administrator is firmware built in to the DuraStor 6200S/7200S external RAID controller installed in the DuraStor RAID appliance. To access Disk Array Administrator, you need s A computer with terminal emulator software, such as HyperTerminal. s A straight-through serial cable. (You cannot use a null modem cable.) Using the cable, connect the computer to an RS-232 serial port on the back of your DuraStor RAID appliance. Connect to Serial A port for Controller 1 or Serial B port for Controller 2. 3-56

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
3-56
DuraStor 6220SS/7220SS Installation and User’s Guide
4
Click
OK
. The Storage Manager Pro Introduction window
appears.
5
Follow the on-screen instructions to complete the installation.
6
When the installation is complete, click
Done
.
The Set Administrator Password window appears.
7
Type a new password, re-enter it to verify it, then click
OK
.
Do
not
click
OK
without changing the password.
Caution:
You
must
supply the password immediately. If you
do not supply the password, you will be unable to log in
after the next reboot, and will have to uninstall and
reinstall Storage Manager Pro.
The installation is complete.
You can now perform all of the functions described in the
Adaptec
Storage Manager Pro User’s Guide
.
Warning:
We strongly recommend that you regularly and
consistently back up your data so that it may be recovered
in the event of a failure that’s not protected by a fault-
tolerant array.
Accessing Disk Array Administrator
Disk Array Administrator is firmware built in to the
DuraStor 6200S/7200S external RAID controller installed in the
DuraStor RAID appliance.
To access Disk Array Administrator, you need
■
A computer with terminal emulator software, such as
HyperTerminal.
■
A straight-through serial cable. (You
cannot
use a null modem
cable.)
Using the cable, connect the computer to an RS-232 serial port on
the back of your DuraStor RAID appliance. Connect to Serial A
port for Controller 1 or Serial B port for Controller 2.
!