Adaptec 1966600 User Guide - Page 72

Stand-Alone Dual-Port (Hubs Disabled), Configuration, Option, Operating Mode, StandAlone Dual Port

Get Adaptec 1966600 - DuraStor 7220SS Hard Drive Array PDF manuals and user guides
UPC - 760884139202
View all Adaptec 1966600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

DuraStor 6220SS/7220SS Installation and User's Guide Stand-Alone Dual-Port (Hubs Disabled) The following diagram illustrates the logical connection of the stand-alone dual-port topology with the hubs disabled. DuraStor FC RAID Appliance CH0 Up to 12 Disk Drives CH1 Up to 12 Disk Drives P2 P1 To FC Switch P3 To FC Switch P4 PHYSICAL FC PORTS DRIVE CHANNELS CH2 FC1 Active CH0 T CH1 FC2 Active T CH2 CH3 T Controller 1 CH3 T ACTIVE T= Location of internal termination. Figure 3-33 Single Host - Hubs Disabled Note: Ports P3 and P4 active. Up to 12 Disk Drives Up to 12 Disk Drives By default the controller's operating mode is set to active-active single-port and the internal hub is set to be Enabled. This topology is for stand-alone dual-port and will need to be changed. If your topology uses the hubs disabled you will need to access the OCP menu and disable this feature. 1 Access the controller menu from the OCP and select the appropriate controller (Controller 1 or Controller 2). 2 From the System menu, select Configuration then select Option Configuration. 3 From the Option Configuration menu, select Operating Mode, select StandAlone Dual Port, then press Enter. 3-38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
3-38
DuraStor 6220SS/7220SS Installation and User’s Guide
Stand-Alone Dual-Port (Hubs Disabled)
The following diagram illustrates the logical connection of the
stand-alone dual-port topology with the hubs disabled.
Figure 3-33
Single Host - Hubs Disabled
Note:
Ports P3 and P4 active.
By default the controller’s operating mode is set to active-active
single-port and the internal hub is set to be
Enabled
. This topology
is for stand-alone dual-port and will need to be changed. If your
topology uses the
hubs disabled
you will need to access the OCP
menu and disable this feature.
1
Access the controller menu from the OCP and select the
appropriate controller (Controller 1 or Controller 2).
2
From the System menu, select
Configuration
then select
Option
Configuration
.
3
From the Option Configuration menu, select
Operating Mode
,
select
StandAlone Dual Port,
then press
Enter
.
P2
FC2
FC1
FC PORTS
T
T
T
T
T= Location of internal termination.
PHYSICAL
DRIVE CHANNELS
DuraStor FC RAID Appliance
Controller 1
ACTIVE
CH0
Up to 12 Disk Drives
To FC Switch
To FC Switch
CH1
CH2
CH3
CH0
CH1
CH2
CH3
P1
P3
P4
Active
Active
Up to 12 Disk Drives
Up to 12 Disk Drives
Up to 12 Disk Drives