Brother International Laura Ashley Innov-ís NX2000 Users Manual - English - Page 47

Page 47 highlights

USEFUL FUNCTIONS d If the "Reverse/Reinforcement Stitch" button is pressed, the machine automatically sews reverse stitches (or reinforcement stitches), cuts the thread, then stops. Pivoting If the pivot setting is selected, the machine stops with the needle lowered (in the fabric) and the presser foot is automatically raised to an appropriate height when the "Start/Stop" button is pressed. When the "Start/Stop" button is pressed again, the presser foot is automatically lowered and sewing continues. This function is useful for stopping the machine to rotate the fabric. a a Reverse stitches (or reinforcement stitches) 2 CAUTION Sewing Basics → The feed dogs are automatically lowered. Memo • The feed dogs are raised when sewing is started. • To cancel the automatic thread cutting setting, press • When the pivot setting is selected, the machine starts when the "Start/Stop" button is pressed or the foot controller is pressed down even if the presser foot has been raised. Be sure to keep your hands and other items away from the needle, otherwise injuries may occur. again so that it appears as . Memo When the pivot setting is selected, the height of the presser foot when sewing is stopped can be changed according to the type of fabric being sewn. Press , and then display "PIVOTING HEIGHT" on p. 2 of the machine settings screen. Press or to select one of the three heights (3.2 mm, 5.0 mm or 7.5 mm). To raise the presser foot further, increase the setting. (Normally, 3.2 mm is set.) Note • If "NEEDLE POSITION" in the machine settings screen (P.1) is set to the raised position, the pivot function cannot be used. • When the setting is selected, the pivot function can only be used with stitches where presser foot J, N, C or O is indicated in the upper-left corner of the screen. If any other stitch is selected, the key appears as a dotted line and is not available. • Since the presser foot is fully raised when the automatic thread cutting key is pressed, press the "Presser Foot Lifter" button to lower the presser foot, and then press the "Start/Stop" button to continue sewing. 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
USEFUL FUNCTIONS
Sewing Basics
45
2
d
If the “Reverse/Reinforcement Stitch” button
is pressed, the machine automatically sews
reverse stitches (or reinforcement stitches),
cuts the thread, then stops.
a
Reverse stitches (or reinforcement stitches)
→
The feed dogs are automatically lowered.
Pivoting
If the pivot setting is selected, the machine stops with
the needle lowered (in the fabric) and the presser foot is
automatically raised to an appropriate height when the
“Start/Stop” button is pressed. When the “Start/Stop”
button is pressed again, the presser foot is automatically
lowered and sewing continues. This function is useful
for stopping the machine to rotate the fabric.
Memo
•
The feed dogs are raised when sewing is started.
•
To cancel the automatic thread cutting setting, press
again so that it appears as
.
a
CAUTION
•
When the pivot setting is selected, the machine
starts when the “Start/Stop” button is pressed or the
foot controller is pressed down even if the presser
foot has been raised. Be sure to keep your hands
and other items away from the needle, otherwise
injuries may occur.
Memo
When the pivot setting is selected, the height of the
presser foot when sewing is stopped can be changed
according to the type of fabric being sewn. Press
, and then display “PIVOTING HEIGHT” on p. 2
of the machine settings screen. Press
or
to
select one of the three heights (3.2 mm, 5.0 mm or 7.5
mm). To raise the presser foot further, increase the
setting. (Normally, 3.2 mm is set.)
Note
•
If “NEEDLE POSITION” in the machine settings
screen (P.1) is set to the raised position, the pivot
function cannot be used.
•
When the setting is selected, the pivot function can
only be used with stitches where presser foot J, N, C
or O is indicated in the upper-left corner of the
screen. If any other stitch is selected, the key
appears as a dotted line and is not available.
•
Since the presser foot is fully raised when the
automatic thread cutting key is pressed, press the
“Presser Foot Lifter” button to lower the presser foot,
and then press the “Start/Stop” button to continue
sewing.