Dell PowerConnect Brocade M6505 Brocade 7.1.0 Fabric Watch Administrator's Gui - Page 45

Tasks > Manage > Switch Admin, Show Advanced Mode, Apply, snmpConfig --set mibcapability

Get Dell PowerConnect Brocade M6505 PDF manuals and user guides View all Dell PowerConnect Brocade M6505 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Interfaces for activating Fabric Watch 4 In Figure 5, the MIB browser populated the left side of the screen with a MIB tree that you can navigate. 3. Open Web Tools and select Tasks > Manage > Switch Admin. 4. Click Show Advanced Mode. 5. On the SNMP tab, enter the IP address of the trap receiver and the severity level, and click Apply. NOTE The severity level must be informational (4) in order to forward threshold alerts. 6. Start a Telnet session, and enter the snmpConfig --set mibcapability command at the prompt to set the SNMP MIB capability. switch:admin> snmpConfig --set mibcapability The SNMP Mib/Trap Capability has been set to support FE-MIB SW-MIB FA-MIB SW-TRAP FA-TRAP FA-MIB (yes, y, no, n): [yes] FICON-MIB (yes, y, no, n): [no] HA-MIB (yes, y, no, n): [no] SW-TRAP (yes, y, no, n): [yes] yes swFCPortScn (yes, y, no, n): [no] swEventTrap (yes, y, no, n): [no] swFabricWatchTrap (yes, y, no, n): [no] yes swTrackChangesTrap (yes, y, no, n): [no] FA-TRAP (yes, y, no, n): [yes] connUnitStatusChange (yes, y, no, n): [no] connUnitEventTrap (yes, y, no, n): [no] connUnitSensorStatusChange (yes, y, no, n): [no] connUnitPortStatusChange (yes, y, no, n): [no] SW-EXTTRAP (yes, y, no, n): [no] switch:admin> 7. Enter the snmpConfig command to configure the SNMP management host IP address. switch:admin> snmpConfig Customizing MIB-II system variables ... At each prompt, do one of the following: o to accept current value, o enter the appropriate new value, o to skip the rest of configuration, or o to cancel any change. To correct any input mistake: erases the previous character, erases the whole line, sysDescr: [Fibre Channel Switch.] sysLocation: [End User Premise.] sysContact: [Field Support.] authTrapsEnabled (true, t, false, f): [false] SNMP community and trap recipient configuration: Community (rw): [Secret C0de] Fabric Watch Administrator's Guide 25 53-1002752-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Fabric Watch Administrator’s Guide
25
53-1002752-01
Interfaces for activating Fabric Watch
4
In
Figure 5
, the MIB browser populated the left side of the screen with a MIB tree that you can
navigate.
3.
Open Web Tools and select
Tasks > Manage > Switch Admin
.
4.
Click
Show Advanced Mode
.
5.
On the
SNMP
tab, enter the IP address of the trap receiver and the severity level, and click
Apply
.
NOTE
The severity level must be informational (4) in order to forward threshold alerts.
6.
Start a Telnet session, and enter the
snmpConfig --set mibcapability
command at the prompt to
set the SNMP MIB capability.
switch:admin>
snmpConfig
--
set mibcapability
The SNMP Mib/Trap Capability has been set to support
FE-MIB
SW-MIB
FA-MIB
SW-TRAP
FA-TRAP
FA-MIB (yes, y, no, n): [yes]
FICON-MIB (yes, y, no, n): [no]
HA-MIB (yes, y, no, n): [no]
SW-TRAP (yes, y, no, n): [yes] yes
swFCPortScn (yes, y, no, n): [no]
swEventTrap (yes, y, no, n): [no]
swFabricWatchTrap (yes, y, no, n): [no] yes
swTrackChangesTrap (yes, y, no, n): [no]
FA-TRAP (yes, y, no, n): [yes]
connUnitStatusChange (yes, y, no, n): [no]
connUnitEventTrap (yes, y, no, n): [no]
connUnitSensorStatusChange (yes, y, no, n): [no]
connUnitPortStatusChange (yes, y, no, n): [no]
SW-EXTTRAP (yes, y, no, n): [no]
switch:admin>
7.
Enter the
snmpConfig
command to configure the SNMP management host IP address.
switch:admin>
snmpConfig
Customizing MIB-II system variables ...
At each prompt, do one of the following:
o <Return> to accept current value,
o enter the appropriate new value,
o <Control-D> to skip the rest of configuration, or
o <Control-C> to cancel any change.
To correct any input mistake:
<Backspace> erases the previous character,
<Control-U> erases the whole line,
sysDescr: [Fibre Channel Switch.]
sysLocation: [End User Premise.]
sysContact: [Field Support.]
authTrapsEnabled (true, t, false, f): [false]
SNMP community and trap recipient configuration:
Community (rw): [Secret C0de]