Epson PowerLite 84 User's Guide - Page 71

Starting the Projector with a Password, mode for approximately 5 minutes. Write down the request code.

Get Epson PowerLite 84 PDF manuals and user guides View all Epson PowerLite 84 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

9. To enable network setting protection, select Network Protect and press Enter. Select On and press Enter. When this feature is on, none of the network settings on the menu can be changed. Starting the Projector with a Password When the password function is enabled, you see this screen when you plug in and turn on the projector: Hold down the Num button on the remote control and use the numeric keypad to enter the four digit password. The password screen closes, the numeric keypad is automatically deactivated, and projection begins. If the password is not correct, you see a message prompting you to re-enter the password. If you enter an incorrect password three times in succession, you see the message The projector's operation will be locked. Request code xxxxx and the projector switches to standby mode for approximately 5 minutes. Write down the request code. Then disconnect the projector's power cord from the electrical outlet, reconnect it, and turn the projector back on. When you see the Password Protect Release screen again, you can try to enter the correct password. If you enter an incorrect password 30 times in succession, the projector remains locked and you must contact Epson to have the projector serviced. Fine-Tuning the Projector 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
Fine-Tuning the Projector
71
9.
To enable network setting protection, select
Network Protect
and press
Enter
. Select
On
and press
Enter
.
When this feature is on, none of the network settings on the
menu can be changed.
Starting the Projector with a Password
When the password function is enabled, you see this screen when you
plug in and turn on the projector:
Hold down the
Num
button on the remote control and use the
numeric keypad to enter the four digit password.
The password screen closes, the numeric keypad is automatically
deactivated, and projection begins.
If the password is not correct, you see a message prompting you to
re-enter the password. If you enter an incorrect password three times
in succession, you see the message
The projector’s operation will be
locked. Request code xxxxx
and the projector switches to standby
mode for approximately 5 minutes. Write down the request code.
Then disconnect the projector’s power cord from the electrical outlet,
reconnect it, and turn the projector back on.
When you see the Password Protect Release screen again, you can try
to enter the correct password.
If you enter an incorrect password 30 times in succession, the
projector remains locked and you must contact Epson to have the
projector serviced.