HP Brio ba200 hp brio ba200, user guide - Page 68

Replacing the Power Supply Unit

Get HP Brio ba200 PDF manuals and user guides View all HP Brio ba200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

Replacing the Power Supply Unit Replacing the Power Supply Unit Warning Hewlett Packard does not support power supply upgrades. This information is provided to help you replace a defective power supply unit. For your safety, only replace with a power supply unit provided by HP Support Services. To avoid electrical shock, do not open the power supply. There are no user-serviceable parts inside. 1 Remove the cover. Refer to page 46. 2 Remove the three screws from the rear of the PC.  Ž 3 Disconnect all power cables from installed drives and from the system board. 4 Lift the power supply unit out of the PC. 5 Place the new power supply unit inside the computer and tighten the three screws on the rear of the PC. 6 Reconnect all the power cables to the drives and the system board. 7 Replace the cover. Refer to page 47. 8 Check that the voltage switch is set correctly for your country (the voltage is set during manufacturing and should already be correct). 62

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
62
Replacing the Power Supply Unit
Replacing the Power Supply Unit
1
Remove the cover. Refer to page 46.
2
Remove the three screws from the rear of the PC.
3
Disconnect all power cables from installed drives and from the system board.
4
Lift the power supply unit out of the PC.
5
Place the new power supply unit inside the computer and tighten the three screws
on the rear of the PC.
6
Reconnect all the power cables to the drives and the system board.
7
Replace the cover. Refer to page 47.
8
Check that the voltage switch is set correctly for your country (the voltage is set
during manufacturing and should already be correct).
Warning
Hewlett Packard does not support power supply upgrades. This information is provided
to help you replace a defective power supply unit.
For your safety, only replace with a
power supply unit provided by HP Support Services.
To avoid electrical shock, do not open the power supply. There are no user-serviceable
parts inside.