HP LH4r Installation and configuration of the HP NetRAID, NetRAID-1 and NetRAI - Page 11

HP NetRAID-3Si External SCSI Cables, HP NetRAID

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Chapter 1 Introduction HP NetRAID-3Si External SCSI Cables Channel 0 External SCSI Cable D6020A(1) 1 D3637C or D6020A 2 D6020A(1) (1) External connections to both Channel 0 and Channel 2 at the same time require two D6020A SCSI Cables. The connectors for Channels 0 and 2 are very close together, and these cables have offset connectors that allow them to fit side-by-side. If the necessary cables were not supplied with your system, see HP's Order Assistant for ordering information. Order Assistant is available on the Internet at http://www.hp.com/go/netserver. HP NetRAID The HP NetRAID adapter supports three channels. It has three connectors for internal SCSI devices and two connectors for external SCSI devices for Channels 0 and 1. Optionally, you can connect an external port to Channel 2. (See Chapter 4, "Planning," for instructions.) Both internal and external connections support: • Fast/Wide SCSI (at data transfer rates of up to 20 MB/sec per channel) • Ultra/Wide SCSI (at data transfer rates of up to 40 MB/sec per channel) The HP NetRAID adapter supports a maximum of six to eight devices per channel depending on the HP system and enclosure used. 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
Chapter 1
Introduction
3
HP NetRAID-3Si External SCSI Cables
Channel
External SCSI Cable
0
D6020A
(1)
1
D3637C or D6020A
2
D6020A
(1)
(1)
External connections to both Channel 0 and Channel 2 at the same time require two
D6020A SCSI Cables. The connectors for Channels 0 and 2 are very close together, and
these cables have offset connectors that allow them to fit side-by-side.
If the necessary cables were not supplied with your system, see HP's Order
Assistant for ordering information. Order Assistant is available on the Internet at
.
HP NetRAID
The HP NetRAID adapter supports three channels. It has three connectors for
internal SCSI devices and two connectors for external SCSI devices for Channels
0 and 1. Optionally, you can connect an external port to Channel 2. (See
Chapter 4, "Planning," for instructions.)
Both internal and external connections support:
•
Fast/Wide SCSI (at data transfer rates of up to 20 MB/sec per channel)
•
Ultra/Wide SCSI (at data transfer rates of up to 40 MB/sec per channel)
The HP NetRAID adapter supports a maximum of six to eight devices per
channel depending on the HP system and enclosure used.