HP LH4r Installation and configuration of the HP NetRAID, NetRAID-1 and NetRAI - Page 56

Step D. Install the Adapter

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Chapter 5 Installation and Configuration Step D. Install the Adapter In this step, you will: • Turn off the HP NetServer and remove the covers • Install the adapter Turn Off the HP NetServer and Remove Cover NOTE Before you begin, you may need to look up information about your HP NetServer in Information Assistant on the HP NetServer Navigator CD-ROM. You will need to know how to remove the HP NetServer panels and cover, and any special instructions for installing a board in a PCI slot of the HP NetServer. Turn off the HP NetServer and remove its cover, as follows: 1. Bring down the operating system properly, as described in your HP NetServer documentation. 2. Turn off the HP NetServer power and disconnect the power cord and all telephone cords. CAUTION Before removing the cover, always disconnect the power cord and unplug telephone cables. Disconnect the power cord to avoid exposure to high energy levels that may cause burns when parts are short-circuited by metal objects, such as tools or jewelry. Disconnect telephone cables to avoid exposure to shock hazard from telephone ringing voltages. Note that the power switch does not turn off standby power in some HP NetServers. Disconnect the power cord to turn off standby power. 3. Remove the HP NetServer panels and cover. 4. Remove the power supplies in an HP NetServer LH Pro or LH II system. This is necessary to connect mass storage cables in these systems. 48

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
Chapter 5
Installation and Configuration
48
Step D. Install the Adapter
In this step, you will:
•
Turn off the HP NetServer and remove the covers
•
Install the adapter
Turn Off the HP NetServer and Remove Cover
NOTE
Before you begin, you may need to look up information about
your HP NetServer in Information Assistant on the
HP NetServer Navigator CD-ROM
. You will need to know
how to remove the HP NetServer panels and cover, and any
special instructions for installing a board in a PCI slot of the
HP NetServer.
Turn off the HP NetServer and remove its cover, as follows:
1.
Bring down the operating system properly, as described in your HP
NetServer documentation.
2.
Turn off the HP NetServer power and disconnect the power cord and all
telephone cords.
CAUTION
Before removing the cover, always disconnect the power cord
and unplug telephone cables. Disconnect the power cord to
avoid exposure to high energy levels that may cause burns
when parts are short-circuited by metal objects, such as tools
or jewelry. Disconnect telephone cables to avoid exposure to
shock hazard from telephone ringing voltages.
Note that the power switch does not turn off standby power in
some HP NetServers. Disconnect the power cord to turn off
standby power.
3.
Remove the HP NetServer panels and cover.
4.
Remove the power supplies in an HP NetServer LH Pro or LH II system.
This is necessary to connect mass storage cables in these systems.