HP ProBook 630 Maintenance and Service Guide - Page 125

Horizontal cable insertion, Multiple-pin horizontal connector (LVDS cable to display panel)

Get HP ProBook 630 PDF manuals and user guides View all HP ProBook 630 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 125 highlights

Horizontal cable insertion Use flat tool to pull connector evenly. Do not pull on cable to remove. Slide connector into receptacle on same horizontal plane as board and use a flat tool to push evenly into receptacle. Multiple-pin horizontal connector (LVDS cable to display panel) Use these procedures to properly insert and remove a multiple-pin horizontal connector. Insert procedure: 1. Slide connector evenly into receptacle on same horizontal plane as PCB connector. 2. Pull lock bar to insert and push both side connector horizontally to firmly lock. 3. Tape down lock bar over the panel to hold in position. Reverse the previous procedure to remove the connector: 1. Remove tape. 2. Pull up bar (pull tape) and release the lock with the PCB connector. 3. Pull to the direction in parallel with PCB to withdraw the connector. Multiple-pin vertical connector (LVDS cable to system board) Use this procedure to properly insert and remove a multiple-pin vertical connector. ● Remove the connector gasket before removing the connector. ● If the connector has a plastic pull tab, pull the tab to disconnect. Otherwise, use flat tool under the connector to remove evenly. Do not pull on the cable to remove. ● Press evenly when reseating, reconnecting, or installing the connector. Additional information 113

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
Horizontal cable insertion
Use flat tool to pull connector evenly. Do not pull on cable to remove.
Slide connector into receptacle on same horizontal plane as board and use a flat tool to push evenly into
receptacle.
Multiple-pin horizontal connector (LVDS cable to display panel)
Use these procedures to properly insert and remove a multiple-pin horizontal connector.
Insert procedure:
1.
Slide connector evenly into receptacle on same horizontal plane as PCB connector.
2.
Pull lock bar to insert and push both side connector horizontally to firmly lock.
3.
Tape down lock bar over the panel to hold in position.
Reverse the previous procedure to remove the connector:
1.
Remove tape.
2.
Pull up bar (pull tape) and release the lock with the PCB connector.
3.
Pull to the direction in parallel with PCB to withdraw the connector.
Multiple-pin vertical connector (LVDS cable to system board)
Use this procedure to properly insert and remove a multiple-pin vertical connector.
●
Remove the connector gasket before removing the connector.
●
If the connector has a plastic pull tab, pull the tab to disconnect. Otherwise, use flat tool under the
connector to remove evenly. Do not pull on the cable to remove.
●
Press evenly when reseating, reconnecting, or installing the connector.
Additional information
113