HP ProLiant DL280 Configuring Arrays on HP Smart Array Controllers Reference G - Page 47

The <target> variable, The <command> variable, Querying a device

Page 47 highlights

The variable This variable provides the path to the device that you want to configure. The device can be a controller, an array, a logical drive, or a physical drive. The syntax used is as follows: controller all | slot=# | wwn=# | chassisname="AAA" | serialnumber=# | chassisserialnumber=# | [array=all|] [logicaldrive all|#] [physicaldrive all|allunassigned For example: controller slot=3 controller wwn=500805F3000BAC11 controller slot=2 array A controller chassisname="A" array B logicaldrive 2 controller chassisname="A" physicaldrive 1:0 controller all controller slot=2 array all controller slot=3 physicaldrive 1:2-1:5 The variable The variable can be any of the following words or phrases, corresponding to typical configuration tasks: add create delete modify remove set target Nonconfiguration commands are also available: diag ("Generating a diagnostic report" on page 53) help ("The help command" on page 51) rescan ("Rescanning the system" on page 54) shorthand ("Keyword abbreviations" on page 48) show ("The show command" on page 49) version ("Displaying the current versions of the application layers" on page 51) A command often requires a parameter, and some parameters require a value, but the specific parameters and values that are valid for a given command depend on the target to which you apply the command. To determine the valid parameters and values for a particular combination of target and command variables, you can query the device ("Querying a device" on page 47). You can also inspect the example commands in other sections of this guide. Querying a device If you do not know what values a parameter can have, you can sometimes query the device to find out by entering a ? as the value of the parameter. Example command: => ctrl ch="Lab4" ld 1 modify raid=0 ss=? A typical screen response in this case could be: Available options are: HP Array Configuration Utility 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123

HP Array Configuration Utility
47
The <target> variable
This variable provides the path to the device that you want to configure. The device can be a controller, an
array, a logical drive, or a physical drive. The syntax used is as follows:
controller all | slot=# | wwn=# | chassisname="AAA" | serialnumber=# |
chassisserialnumber=# | [array=all|<id>] [logicaldrive all|#]
[physicaldrive all|allunassigned|[#:]#:#,[#:]#:#...|[#:]#:#-[#:]#:#]
For example:
controller slot=3
controller wwn=500805F3000BAC11
controller slot=2 array A
controller chassisname="A" array B logicaldrive 2
controller chassisname="A" physicaldrive 1:0
controller all
controller slot=2 array all
controller slot=3 physicaldrive 1:2-1:5
The <command> variable
The
<command>
variable can be any of the following words or phrases, corresponding to typical
configuration tasks:
add
create
delete
modify
remove
set target
Nonconfiguration commands are also available:
diag
("
Generating a diagnostic report
" on page
53
)
help
("
The help command
" on page
51
)
rescan
("
Rescanning the system
" on page
54
)
shorthand
("
Keyword abbreviations
" on page
48
)
show
("
The show command
" on page
49
)
version ("
Displaying the current versions of the application layers
" on page
51
)
A command often requires a parameter, and some parameters require a value, but the specific parameters
and values that are valid for a given command depend on the target to which you apply the command.
To determine the valid parameters and values for a particular combination of target and command variables,
you can query the device ("
Querying a device
" on page
47
). You can also inspect the example commands
in other sections of this guide.
Querying a device
If you do not know what values a parameter can have, you can sometimes query the device to find out by
entering a
?
as the value of the parameter.
Example command:
=> ctrl ch="Lab4" ld 1 modify raid=0 ss=?
A typical screen response in this case could be:
Available options are: