HP ProLiant DL280 Configuring Arrays on HP Smart Array Controllers Reference G - Page 58

Viewing enclosure information, Viewing physical drives for an HBA, Syntax, Command examples

Get HP ProLiant DL280 PDF manuals and user guides View all HP ProLiant DL280 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

When moving the logical drive, you can choose one of the following destinations: • An existing array • A new array you create To move a logical drive to an existing array, use the following information. Syntax: modify [newarray=] Command examples: ctrl slot=1 ld 3 modify newarray=C ctrl slot=1 ld 3 modify newarray=? // shows the available arrays To move a logical drive and create a new array, use the following information. Syntax: modify [drives Command examples: ctrl slot=1 ld 3 modify drives=2e:1:1-2e:1:4 ctrl slot=1 ld 3 modify drives=? // shows the available drives You can use the drivetype parameter to specify the drive interface type. When selecting all physical drives, and multiple drive types exist, you must specify the drive interface type. Mixed drives are not allowed on the same array or logical drives. If all drives on a controller are the same type, this parameter is not needed. For drivetype, use one of the following valid options: [drivetype=sas | satalogical | sata | saslogical | parallelscsi | ss_sas | ss_sata | ?] Command examples: controller slot=5 ld 1 modify drives=? drivetype=sas controller slot=5 array A modify drives=? drivetype=ss_sas Viewing enclosure information The enclosure keyword is a valid target for the show command, and it outputs the storage enclosure information. Syntax: enclosure [ all | port:box | serialnumber=xxx ] show [ detail | status ] where the target can be any valid storage controller. Example commands: controller slot=5 enclosure all show controller slot=5 enclosure 4E:1 show detail controller slot=5 enclosure serialnumber=UAB123456 show status Viewing physical drives for an HBA The nonsa keyword shows the physical drives behind an HBA or "non-smart array." Syntax: nonsa show [ssdinfo] Command examples: controller nonsa show controller nonsa show ssdinfo HP Array Configuration Utility 58

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
HP Array Configuration Utility
58
When moving the logical drive, you can choose one of the following destinations:
•
An existing array
•
A new array you create
To move a logical drive to an existing array, use the following information.
Syntax:
<target> modify [newarray=]
Command examples:
ctrl slot=1 ld 3 modify newarray=C
ctrl slot=1 ld 3 modify newarray=? // shows the available arrays
To move a logical drive and create a new array, use the following information.
Syntax:
<target> modify [drives=[#: ]#:#,[#: ]#:#,[#: ]#:#–[#: ]#:#,...]
Command examples:
ctrl slot=1 ld 3 modify drives=2e:1:1-2e:1:4
ctrl slot=1 ld 3 modify drives=? // shows the available drives
You can use the
drivetype
parameter to specify the drive interface type. When selecting all physical
drives, and multiple drive types exist, you must specify the drive interface type. Mixed drives are not allowed
on the same array or logical drives. If all drives on a controller are the same type, this parameter is not
needed.
For
drivetype
, use one of the following valid options:
[drivetype=sas | satalogical | sata | saslogical | parallelscsi | ss_sas |
ss_sata | ?]
Command examples:
controller slot=5 ld 1 modify drives=? drivetype=sas
controller slot=5 array A modify drives=? drivetype=ss_sas
Viewing enclosure information
The
enclosure
keyword is a valid target for the
show
command, and it outputs the storage enclosure
information.
Syntax:
enclosure [ all | port:box | serialnumber=xxx ] show [ detail | status ]
where the target can be any valid storage controller.
Example commands:
controller slot=5 enclosure all show
controller slot=5 enclosure 4E:1 show detail
controller slot=5 enclosure serialnumber=UAB123456 show status
Viewing physical drives for an HBA
The
nonsa
keyword shows the physical drives behind an HBA or "non-smart array."
Syntax:
<target> nonsa show [ssdinfo]
Command examples:
controller nonsa show
controller nonsa show ssdinfo