HP ProLiant DL280 Configuring Arrays on HP Smart Array Controllers Reference G - Page 49

The show command, Keyword, Abbreviation in ACU, ACU CLI, Syntax, Example 1

Get HP ProLiant DL280 PDF manuals and user guides View all HP ProLiant DL280 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Keyword Abbreviation in ACU Keyword CLI Abbreviation in ACU CLI licensekey logicaldrive mnpdelay lk ld mnpd tapedrive td waitforcacheroom wfcr - - *The CLI also uses this keyword and abbreviation for the terms box name and RAID array ID. The show command The show command enables you to obtain information about a device. Syntax: show [detail]|[status] When you specify a target that consists of several devices, the information in the output is normally less comprehensive than when you specify only one device as the target. You can use the [detail] parameter in this case to retain all the information usually given for individual devices. An extra parameter is available for controller targets: config. This parameter is used as follows: show config [detail] If you use the config parameter, the output includes information about each device connected to the controller. Example 1 => ctrl slot=9 show A typical output would be: Smart Array P421 in Slot 9 Bus Interface: PCI Slot: 9 Serial Number: PBKTV0XTAZZ005 RAID 6 (ADG) Status: Enabled Controller Status: OK Hardware Revision: A Firmware Version: 0.02-106 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 3 secs Surface Scan Mode: Idle Queue Depth: Automatic Monitor and Performance Delay: 60 min Elevator Sort: Enabled Degraded Performance Optimization: Disabled Inconsistency Repair Policy: Disabled Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 15 secs Cache Board Present: True Cache Status: OK HP Array Configuration Utility 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
HP Array Configuration Utility
49
Keyword
Abbreviation in ACU
CLI
Keyword
Abbreviation in
ACU CLI
licensekey
lk
tapedrive
td
logicaldrive
ld
waitforcacheroom
wfcr
mnpdelay
mnpd
—
—
*The CLI also uses this keyword and abbreviation for the terms
box name
and
RAID array ID
.
The show command
The
show
command enables you to obtain information about a device.
Syntax:
<target> show [detail]|[status]
When you specify a target that consists of several devices, the information in the output is normally less
comprehensive than when you specify only one device as the target. You can use the
[detail]
parameter
in this case to retain all the information usually given for individual devices.
An extra parameter is available for controller targets:
config
. This parameter is used as follows:
<target controller> show config [detail]
If you use the
config
parameter, the output includes information about each device connected to the
controller.
Example 1
=> ctrl slot=9 show
A typical output would be:
Smart Array P421 in Slot 9
Bus Interface: PCI
Slot: 9
Serial Number: PBKTV0XTAZZ005
RAID 6 (ADG) Status: Enabled
Controller Status: OK
Hardware Revision: A
Firmware Version: 0.02-106
Rebuild Priority: Medium
Expand Priority: Medium
Surface Scan Delay: 3 secs
Surface Scan Mode: Idle
Queue Depth: Automatic
Monitor and Performance Delay: 60 min
Elevator Sort: Enabled
Degraded Performance Optimization: Disabled
Inconsistency Repair Policy: Disabled
Wait for Cache Room: Disabled
Surface Analysis Inconsistency Notification: Disabled
Post Prompt Timeout: 15 secs
Cache Board Present: True
Cache Status: OK