IBM 8651RM0 Hardware Maintenance Manual - Page 117

Microprocessor Installation

Get IBM 8651RM0 - Netfinity 7000 - 8651 PDF manuals and user guides
UPC - 087944340508
View all IBM 8651RM0 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 117 highlights

A microprocessor/heat-sink assembly might contain the following components. . ... . ..... ..... . ... . ..... ..... . ... . ..... 1 Heat-sink retention clip 2 Heat sink 3 Microprocessor 4 Latch 5 Secondary microprocessor socket, empty, with latch in open position 6 Primary microprocessor socket, with latch in closed, locked position You will work with these components while performing the steps in this section. Microprocessor Installation: To install a microprocessor: 1. Power-off the server and peripheral devices and disconnect all external cables and power cords; then, remove the top cover (see "Cover (Top)" on page 72). Caution If the server has been operating, the heat sinks on the installed microprocessors will be hot. Let the components cool for 10 minutes before continuing with the procedures. 2. Determine the processor board on which you want to install the microprocessor. IBM Netfinity 7000 - Type 8651 109

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
A microprocessor/heat-sink assembly might contain the
following components.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
1
Heat-sink retention clip
2
Heat sink
3
Microprocessor
4
Latch
5
Secondary microprocessor socket, empty, with
latch in open position
6
Primary microprocessor socket, with latch in
closed, locked position
You will work with these components while performing the
steps in this section.
Microprocessor Installation:
To install a
microprocessor:
1.
Power-off the server and peripheral devices and
disconnect all external cables and power cords; then,
remove the top cover (see “Cover (Top)” on
page 72).
Caution
If the server has been operating, the heat sinks
on the installed microprocessors will be hot.
Let
the components cool for 10 minutes before
continuing with the procedures.
2.
Determine the processor board on which you want to
install the microprocessor.
IBM Netfinity 7000 - Type 8651
109