IBM 8681 Hardware Maintenance Manual - Page 184

Power control card LED, the system has a 240VA fault, which will shut down

Get IBM 8681 - Eserver xSeries 370 PDF manuals and user guides
UPC - 087944642503
View all IBM 8681 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 184 highlights

Power control card LED The power control card LED is located in the center of the system, between the processors and the midplane. On the power control card is an LED that provides status of the card based on its flash rate. To view the LED, look through the hole in the left side of the chassis. With AC power applied to the power supplies, the following conditions may be indicated by the power control card LED: 1. Slow flash rate (approximately 1 flash per second) the power control card is functioning properly. 2. No flashing LED - Power control card is not operational. Replace the power control card. 3. Fast flash rate (approximately 2 flashes per second) the system has a 240VA fault, which will shut down the system, indicating a possible processor failure or a short in a system component. If a 240VA fault is indicated (LED flashing rapidly), do the following: 1. Leave the AC power applied. 2. Connect to the service processor and view the system error log, looking for a power failure message on one or more of the power planes. If a power failure message is posted, refer to the following table and proceed as indicated. 176 Netfinity Server HMM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
Power control card LED
The power control card LED is located in the center of the
system, between the processors and the midplane. On the
power control card is an LED that provides status of the
card based on its flash rate.
To view the LED, look
through the hole in the left side of the chassis.
With AC power applied to the power supplies, the following
conditions may be indicated by the power control card
LED:
1.
Slow flash rate (approximately 1 flash per second) -
the power control card is functioning properly.
2.
No flashing LED - Power control card is not
operational.
Replace the power control card.
3.
Fast flash rate (approximately 2 flashes per second) -
the system has a 240VA fault, which will shut down
the system, indicating a possible processor failure or
a short in a system component.
If a 240VA fault is indicated (LED flashing rapidly), do the
following:
1.
Leave the AC power applied.
2.
Connect to the service processor and view the
system error log, looking for a power failure message
on one or more of the power planes. If a power failure
message is posted, refer to the following table and
proceed as indicated.
176
Netfinity Server HMM