IBM 88643RU Service Guide - Page 60

Hot-swapping, memory, module

Get IBM 88643RU - System x3850 - 8864 PDF manuals and user guides
UPC - 000435958211
View all IBM 88643RU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

DIMM Retaining clip 8. Insert the DIMM into the connector by aligning the edges of the DIMM with the slots at the ends of the DIMM connector. 9. Firmly press one end of the DIMM into the connector; then, press the other end into the connector. The retaining clips snap into the locked position when the DIMM is seated in the connector. If there is a gap between the DIMM and the retaining clips, the DIMM has not been correctly inserted; open the retaining clips, remove the DIMM, and then reinsert it. 10. Repeat steps 5 through 9 to install the second DIMM in the pair and for each additional pair that you install. 11. Replace the memory card: a. Insert the memory card into the memory card connector. b. Press the memory card into the connector and close the retention levers. 12. Reconnect external cables and power cords. Hot-swapping a memory module: To hot-swap memory modules, complete the following steps: 1. Read the safety information that begins on page vii, and "Handling static-sensitive devices" on page 31. Attention: Static electricity that is released to internal server components when the server is powered-on might cause the server to halt, which could result in the loss of data. To avoid this potential problem, always use an electrostatic-discharge wrist strap or other grounding system when working inside the server with the power on. 2. Remove the top cover "Removing the cover and bezel" on page 31. Attention: When moving the memory card, do not allow it to impact any components or structures inside the server. Make sure that the Memory Hot-Swap Enabled LED is lit. 44 IBM System x3850 Type 8864: Problem Determination and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
DIMM
Retaining
clip
8.
Insert
the
DIMM
into
the
connector
by
aligning
the
edges
of
the
DIMM
with
the
slots
at
the
ends
of
the
DIMM
connector.
9.
Firmly
press
one
end
of
the
DIMM
into
the
connector;
then,
press
the
other
end
into
the
connector.
The
retaining
clips
snap
into
the
locked
position
when
the
DIMM
is
seated
in
the
connector.
If
there
is
a
gap
between
the
DIMM
and
the
retaining
clips,
the
DIMM
has
not
been
correctly
inserted;
open
the
retaining
clips,
remove
the
DIMM,
and
then
reinsert
it.
10.
Repeat
steps
5
through
9
to
install
the
second
DIMM
in
the
pair
and
for
each
additional
pair
that
you
install.
11.
Replace
the
memory
card:
a.
Insert
the
memory
card
into
the
memory
card
connector.
b.
Press
the
memory
card
into
the
connector
and
close
the
retention
levers.
12.
Reconnect
external
cables
and
power
cords.
Hot-swapping
a
memory
module:
To
hot-swap
memory
modules,
complete
the
following
steps:
1.
Read
the
safety
information
that
begins
on
page
vii,
and
“Handling
static-sensitive
devices”
on
page
31.
Attention:
Static
electricity
that
is
released
to
internal
server
components
when
the
server
is
powered-on
might
cause
the
server
to
halt,
which
could
result
in
the
loss
of
data.
To
avoid
this
potential
problem,
always
use
an
electrostatic-discharge
wrist
strap
or
other
grounding
system
when
working
inside
the
server
with
the
power
on.
2.
Remove
the
top
cover
“Removing
the
cover
and
bezel”
on
page
31.
Attention:
When
moving
the
memory
card,
do
not
allow
it
to
impact
any
components
or
structures
inside
the
server.
Make
sure
that
the
Memory
Hot-Swap
Enabled
LED
is
lit.
44
IBM
System
x3850
Type
8864:
Problem
Determination
and
Service
Guide