IBM HS22 User Guide - Page 75

Force Legacy Video on Boot, Devices and I/O Ports - power consumption

Get IBM HS22 - BladeCenter - 7870 PDF manuals and user guides
UPC - 883436054232
View all IBM HS22 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

- Devices and I/O Ports Select this choice to view or change assignments for devices and input/output (I/O) ports. You can configure the remote console redirection, enable or disable integrated Ethernet controllers, and the SAS controller. If you disable a device, it cannot be configured, and the operating system will not be able to detect it (this is equivalent to disconnecting the device). - Power Select this choice to view or change power capping to control power consumption and processor performance states. - Legacy Support Select this choice to view or set legacy support. - Force Legacy Video on Boot Select this choice to force INT video support, if the operating system does not support UEFI video output standards. - Rehook INT Select this choice to enable or disable devices from taking control of the boot process. The default is Disable. - Legacy Thunk Support Select this choice to enable or disable UEFI to interact with PCI mass storage devices that are non-UEFI compliant. - Integrated Management Module Select this choice to view or change the settings for the integrated management module. - POST Watchdog Timer Select this choice to view or enable the POST watchdog timer. - POST Watchdog Timer Value Select this choice to view or set the POST loader watchdog timer value. - Reboot System on NMI Enable or disable restarting the system whenever a nonmaskable interrupt (NMI) occurs. Disabled is the default. - Network Configuration Select this choice to view the system management network interface port, the IMM MAC address, the current IMM IP address, and host name; define the static IMM IP address, subnet mask, and gateway address, specify whether to use the static IP address or have DHCP assign the IMM IP address, save the network changes, and reset the IMM. - Reset IMM to Defaults Select this choice to view or reset IMM to the default settings. - System Security Select this choice to view or configure security options. - Adapters and UEFI Drivers Select this choice to view information about the adapters and UEFI drivers installed in the server. - Network Select this choice to view or configure the network device options, such as iSCSI, PXE, and Broadcom. - Trusted Platform Module (TPM) Select this choice to view and configure TPM settings. Chapter 4. Configuring the blade server 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
–
Devices and I/O Ports
Select this choice to view or change assignments for devices and
input/output (I/O) ports. You can configure the remote console redirection,
enable or disable integrated Ethernet controllers, and the SAS controller. If
you disable a device, it cannot be configured, and the operating system will
not be able to detect it (this is equivalent to disconnecting the device).
–
Power
Select this choice to view or change power capping to control power
consumption and processor performance states.
–
Legacy Support
Select this choice to view or set legacy support.
-
Force Legacy Video on Boot
Select this choice to force INT video support, if the operating system does
not support UEFI video output standards.
-
Rehook INT
Select this choice to enable or disable devices from taking control of the
boot process. The default is
Disable
.
-
Legacy Thunk Support
Select this choice to enable or disable UEFI to interact with PCI mass
storage devices that are non-UEFI compliant.
–
Integrated Management Module
Select this choice to view or change the settings for the integrated
management module.
-
POST Watchdog Timer
Select this choice to view or enable the POST watchdog timer.
-
POST Watchdog Timer Value
Select this choice to view or set the POST loader watchdog timer value.
-
Reboot System on NMI
Enable or disable restarting the system whenever a nonmaskable interrupt
(NMI) occurs.
Disabled
is the default.
-
Network Configuration
Select this choice to view the system management network interface port,
the IMM MAC address, the current IMM IP address, and host name; define
the static IMM IP address, subnet mask, and gateway address, specify
whether to use the static IP address or have DHCP assign the IMM IP
address, save the network changes, and reset the IMM.
-
Reset IMM to Defaults
Select this choice to view or reset IMM to the default settings.
–
System Security
Select this choice to view or configure security options.
–
Adapters and UEFI Drivers
Select this choice to view information about the adapters and UEFI drivers
installed in the server.
–
Network
Select this choice to view or configure the network device options, such as
iSCSI, PXE, and Broadcom.
–
Trusted Platform Module (TPM)
Select this choice to view and configure TPM settings.
Chapter 4. Configuring the blade server
61