Icom ID-5100A Full Instruction Manual - Page 306

Previous view 13 OTHER FUNCTIONS Remote jack (CI-V) information (Continued) DDCommand table Cmd. Sub cmd. Data Description 00 see p. 13-18 Send operating frequency for transceive 01 see p. 13-18 Send operating mode for transceive 03 see p. 13-18 Read operating frequency 04 see p. 13-18 Read operating mode 05 see p. 13-18 Send operating frequency 06 see p. 13-18 Send operating mode 07 D0 Select A band Dualwatch: Set the Main band as the A band Single watch: Select the A band D1 Select B band Dualwatch: Set the Main band as the B band Single watch: Select the B band 0C see p. 13-18 Read frequency offset*1 0D see p. 13-18 Send frequency offset 0F Read duplex setting (10=simplex, 11=DUP-, 12=DUP+) 10 Set simplex operation 11 Set DUP- operation 12 Set DUP+ operation 14 01 0000 to 0255 Send/read audio output level (000=Minimum, 0128=Center, 0255=Maximum) 03 0000 to 0255 Send/read squelch level (000=Minimum, 0128=Center, 0255=Maximum) 0A see p. 13-18 Send/read RF power setting 0B see p. 13-18 Send/read external microphone gain. 16 see p. 13-18 Send/read VOX gain. 15 01 00 Read noise/S-meter squelch status (squelch close) 01 Read noise/S-meter squelch status (squelch open) 02 0000 to 0255 Read S-meter level (0000=S0, 0170=S9) 05 00 Read tone squelch and RF squelch status (squelch close) 01 Read tone squelch and RF squelch status (squelch open) 11 0000 to 0255 Read RF power meter (0026=LOW, 0077=MID, 0255=HIGH) 16 42 00 Send/read Repeater tone OFF 01 Send/read Repeater tone ON 43 00 Send/read Tone squelch OFF 01 Send/read Tone squelch ON 02 Send/read Reversed Tone squelch ON 46 00 Send/read VOX function OFF 01 Send/read VOX function ON 4B 00 Send/read DTCS OFF 01 Send/read DTCS ON 02 Send/read Reversed DTCS ON 59 00 Send/read single watch mode 01 Send/read Dualwatch mode 5B 00 Send/read DSQL/CSQL OFF (DV mode only) 01 Send/read DSQL ON (DV mode only) 02 Send/read CSQL ON (DV mode only) 5C 00, 01, 02 Send/read GPS TX mode (00=OFF, 01=D-PRS, 02=NMEA) 18 00 Turning the transceiver power OFF 01 Turning the transceiver power ON*2 19 00 Read transceiver ID 1B 00 see p. 13-18 Send/read Repeater tone frequency 01 see p. 13-18 Send/read Tone squelch frequency 02 see p. 13-18 Send/read DTCS code and polarity 07 see p. 13-18 Send/read CSQL code (DV mode) 1C 00 00 Send/read Transceiver's status (RX) 01 Send/read Transceiver's status (TX) Cmd. Sub cmd. 1F 00 01 02 20 00 00 01 02 01 00 01 02 02 00 01 02 03 00 01 02 04 00 01 02 22 00 01 00 01 02 23 00 01 02 24 00 00 01 Data see p. 13-18 see p. 13-19 see p. 13-19 00*3 01*3 see p. 13-19 see p. 13-19 00*3 01*3 see p. 13-20 see p. 13-20 00*3 01*3 see p. 13-20 see p. 13-20 00 01 see p. 13-20 see p. 13-20 00 01 see p. 13-22 see p. 13-22 see p. 13-22 00 01 see p. 13-22 00, 01 see p. 13-22 00 01 03 see p. 13-22 00 01 00 01 Description Send/read DV MY call sign Send/read DV TX call signs Send/read DV TX message Send/read Auto DV RX Call signs output OFF Send/read Auto DV RX Call signs output ON Output DV RX Call signs for transceive Read DV RX Call signs for transceive Send/read Auto DV RX message output OFF Send/read Auto DV RX message output ON Output DV RX message for transceive Read DV RX message for transceive Send/read Auto DV RX status output OFF Send/read Auto DV RX status output ON Output DV RX status for transceive Read DV RX status for transceive Send/read Auto DV RX GPS/D-PRS data output OFF Send/read Auto DV RX GPS/D-PRS data output ON Output DV RX GPS/D-PRS data for transceive Read DV RX GPS/D-PRS data for transceive Send/read Auto DV RX GPS/D-PRS message output OFF Send/read Auto DV RX GPS/D-PRS message output ON Output DV RX GPS/D-PRS message for transceive Read DV RX GPS/D-PRS message for transceive Send/read DV TX data (Up to 30 byte) Send/read Auto DV RX data output OFF Send/read Auto DV RX data output ON Send/read DV RX data (Up to 30 byte) Send/read DV data TX setting (00=PTT, 01=Auto) Read the position Send/read the internal GPS OFF Send/read the internal GPS ON Send/read the manual input Send/read manually input position Send/read TX output power setting OFF Send/read TX output power setting ON TX output power setting OFF for transceive TX output power setting ON for transceive *1Below 100 Hz is omitted. *2W hen sending the power ON command (18 01), the command "FE" must be sent before the basic format. • 19200bps: 25 • 9600bps: 13 • 4800bps: 7 e.g.: When operating with 4800 bps q w e r t u FEF EFE 8CE O 1 8 01 F D ×7 q Preamble code (fixed) w Transceiver's default address e Controller's default address r Command number t Sub command number u End of message code (fixed) *3Output setting is automatically turned OFF after turning the power OFF, then ON. 13-17