Icom VE-PG4 Installation Guide ver.1.34 - Page 57

Before using the wireless LAN transceiver controller, Installation overview

Get Icom VE-PG4 PDF manuals and user guides View all Icom VE-PG4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

3 Wireless LAN transceivers Before using the wireless LAN transceiver controller ■■Installation overview The following shows a typical setting procedure for the wireless LAN transceiver controller on the VE-PG4 Setting screen. 1 Network Settings > IP Address Enter the IP address according to your network environment. (Default: 192.168.0.1) Network Settings > DHCP Server Enable or disable the VE-PG4's DHCP server function. (Default: Disable) 2 Transceiver Controller > Transceiver settings > Transceiver Registration Transceiver Controller > Common Settings Enter the Transceiver Model, Name and Unit ID, Password and Setting group. LLThe default password is "iptrx". You can change it for security. LLCustomize the common settings for the transceiver group (Tenant) on the Common Settings screen. Setting by the CS-IP100H cloning software After IP100Hs are registered to the RoIP Gateway, set the wireless LAN settings, antenna settings (internal or external), provisioning server settings (RoIP Gateway) for all the IP100Hs. LLThe CS-IP100H cloning software can be downloaded from the Icom website. Refer to the IP100H instructions for details. 3 Transceiver Controller > Transceiver settings > Transceiver settings Set the functions, such as Communication Method (Simplex or Full-Duplex), Priority Call, Area Call, Message, and Status, for each transceiver. Enable the required functions for all the IP100Hs that are registered on the Transceiver Registration screen. •• Use ID list • Communication Method (Simplex/Full-duplex) •• Priority Call • Area Call •• Message • Status 4 Destination Settings > Destination Settings Assign the registered IP100Hs or IP100FS on the Transceiver Registration screen to a group. The group ID and the communication type are set on the Destination Settings screen. NOTE: Applying the settings to the IP100H If the RoIP Gateway's setup has been changed, be sure to restart the IP100H to apply the setting. 3-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
3
WIRELESS LAN TRANSCEIVERS
3-2
■
Installation overview
Before using the wireless LAN transceiver controller
The following shows a typical setting procedure for the wireless LAN transceiver controller on the VE-PG4
Setting screen.
1
Network Settings > IP Address
Enter the IP address
according to your network environment. (Default: 192.168.0.1)
Network Settings > DHCP Server
Enable or disable the VE-PG4’s DHCP server function. (Default: Disable)
2
Transceiver Controller > Transceiver settings > Transceiver Registration
Transceiver Controller > Common Settings
Enter the Transceiver Model, Name and Unit ID, Password and Setting group.
L
The default password is “iptrx”. You can change it for security.
L
Customize the common settings for the transceiver group (Tenant) on the Common Settings screen.
Setting by the CS-IP100H
CLONING
SOFTWARE
After IP100Hs are registered to the RoIP Gateway, set the wireless LAN settings, antenna settings
(internal or external), provisioning server settings (RoIP Gateway) for all the IP100Hs.
L
The CS-IP100H
CLONING
SOFTWARE
can be downloaded from the Icom website. Refer to the IP100H instructions
for details.
3
Transceiver Controller > Transceiver settings > Transceiver settings
Set the functions, such as Communication Method (Simplex or Full-Duplex), Priority Call, Area Call,
Message, and Status, for each transceiver.
Enable the required functions for all the IP100Hs that are registered on the Transceiver Registration
screen.
•
Use ID list
• Communication Method (Simplex/Full-duplex)
•
Priority Call
• Area Call
• Message
• Status
4
Destination Settings > Destination Settings
Assign the registered IP100Hs or IP100FS on the Transceiver Registration screen to a group.
The group ID and the communication type are set on the Destination Settings screen.
NOTE: Applying the settings to the IP100H
If the RoIP Gateway’s setup has been changed, be sure to restart the IP100H to apply the setting.