Intel SR2600UR Service Guide - Page 75

Removing a PCI Add-in Card, Installing the PCI Riser Assembly on Removing the PCI Riser

Get Intel SR2600UR - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858206778
View all Intel SR2600UR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

8. Install the PCI riser assembly into the server system. For instructions, see "Installing the PCI Riser Assembly" on page 51. Removing a PCI Add-in Card To remove a PCI add-in card, follow these steps: 1. Remove the PCI riser assembly. For instructions, see "Removing the PCI Riser Assembly" on page 50. 2. Open the rear retention clip by pushing the blue slide upward and rotating clip to the fully open position (see letter "A" in Figure 37). 3. Open the front retention clip by rotating 90 degrees outward (see letter "B" in Figure 37). 4. Remove the PCI add-in card from the riser card connector (see letter "C" in Figure 37). A D C B AF002970 Figure 37. Removing a Full-height Add-In Card 5. Install the filler panel (see letter "D" in Figure 37). 6. Close the rear retention clip. Push the blue slide upward and press the clip to lock it into place. 7. Close the front retention clip and push the blue latch forward to lock it into place. Note: Make sure that all empty add-in card slots have filler panels installed. 8. Install the PCI riser assembly into the server system. For instructions, see "Installing the PCI Riser Assembly" on page 51. Intel® Server System SR2600UR/SR2625UR Service Guide 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
Intel
®
Server System SR2600UR/SR2625UR Service Guide
55
8.
Install the PCI riser assembly into the server system. For instructions, see
“Installing the PCI Riser Assembly” on page 51
.
Removing a PCI Add-in Card
To remove a PCI add-in card, follow these steps:
1.
Remove the PCI riser assembly. For instructions, see
“Removing the PCI Riser
Assembly” on page 50
.
2.
Open the rear retention clip by pushing the blue slide upward and rotating clip to
the fully open position (see letter “A” in
Figure 37
).
3.
Open the front retention clip by rotating 90 degrees outward (see letter “B” in
Figure 37
).
4.
Remove the PCI add-in card from the riser card connector (see letter “C” in
Figure 37
).
Figure 37. Removing a Full-height Add-In Card
5.
Install the filler panel (see letter “D” in
Figure 37
).
6.
Close the rear retention clip. Push the blue slide upward and press the clip to lock it
into place.
7.
Close the front retention clip and push the blue latch forward to lock it into place.
Note:
Make sure that all empty add-in card slots have filler panels installed.
8.
Install the PCI riser assembly into the server system. For instructions, see
“Installing the PCI Riser Assembly” on page 51
.
B
A
D
C
AF002970