Home » Lexmark Manuals » Multifunction Devices » Lexmark X644E » Manual Viewer

Lexmark X644E User's Guide - Page 78

Labels

UPC - 734646093156

Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

Understanding paper and specialty media guidelines Labels The MFP can print on many labels designed for use with laser printers. These labels are supplied in letter size, A4 size, and legal size sheets. Label adhesives, face sheet (printable stock), and topcoats must be able to withstand temperatures of 230°C (446°F) and pressure of 25 pounds per square inch (psi). Try a sample of any labels you are considering using with the MFP before purchasing a large quantity. For detailed information on label printing, characteristics, and design, see the Card Stock & Label Guide available on the Lexmark Web site at www.lexmark.com/publications. Note: Labels are one of the most difficult print media for laser MFPs. All MFP models require a special fuser cleaner for label applications to optimize feed reliability. See Ordering supplies for information on obtaining a label fuser cleaner. After printing approximately 10,000 pages of labels (or each time you replace the print cartridge), complete the following steps to maintain MFP feeding reliability: 1 Print five sheets of paper. 2 Wait approximately five seconds. 3 Print five more sheets of paper. When printing on labels: • Set the Paper Size/Type menu item to Labels in the Paper menu. You can set the Paper Size/Type from the MFP control panel, the MFP driver, or from MarkVision. • Feed vinyl labels from the standard 250- or 500-sheet trays or the optional 250- or 500-sheet drawers. For vinyl labels, set the Paper Type to Labels, the Labels Texture to Smooth, and the Label Weight to Heavy, or set the Paper Type to vinyl labels and the texture and weight to normal. • Do not load labels with paper or transparencies in the same source; mixing print media can cause feeding problems and print quality problems. • Do not use label sheets with a slick backing material. • Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a jam. Partial sheets also contaminate the MFP and your cartridge with adhesive, and could void the MFP and cartridge warranties. • Use labels that can withstand temperatures of 230°C (446°F) without sealing, excessive curling, wrinkling, or releasing hazardous emissions. • Do not print within 1 mm (0.04 in.) of the edge of the label, of the perforations, or between die-cuts of the label. • Do not use label sheets that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive at least 1 mm (0.04 in.) away from edges. Adhesive material contaminates the MFP and could void the warranty. • If zone coating of the adhesive is not possible, a 1.6 mm (0.1 in.) strip should be removed on the leading and driver edge, and a non-oozing adhesive should be used. • Remove a 1.6 mm (0.1 in.) strip from the leading edge to prevent labels from peeling inside the MFP. • Portrait orientation is preferred, especially when printing bar codes. • Do not use labels that have exposed adhesive. Selecting print media 78

Section	Page
Contents	4
Learning about the MFP	8
Identifying the MFP	8
Models	8
Using the scanner	9
Basic functions of the scanner	9
Automatic document feeder and flatbed	9
Configured models	10
Understanding the MFP control panel	11
Home screen and Home screen buttons	14
Using the LCD touch-screen buttons	17
Sample screen one	17
Information on touch-screen buttons	17
Sample screen two	19
Information on touch-screen buttons	19
Other touch-screen buttons	20
Features	22
Menus	23
Copying	24
Quick copy	24
Multiple page copying	24
Using the flatbed	25
Understanding the copy screens and options	25
Copying from one size to another	27
Making transparencies	27
Copying to letterhead	27
Copying photographs	27
Making copies using media from a selected tray	28
Copying mixed-sized media	28
Setting the duplex option	29
Reducing and enlarging copies	29
Adjusting copy quality	29
Setting collation options	30
Placing separator sheets between copies	30
Setting paper saving options	30
Placing the date and time at the top of each page	31
Placing an overlay message on each page	31
Creating a custom job (job build)	31
Canceling a copy job	32
While the document is in the ADF	32
While copying pages using the flatbed	32
When the pages are being printed	32
Copy tips	32
E-mail	33
Entering an e-mail address	33
Using a shortcut number	33
Using the address book	34
E-mailing to a profile	34
Adding e-mail subject and message information	34
Changing the output file type	35
E-mailing color documents	35
Creating an e-mail shortcut	35
From a computer	35
From the MFP	36
Creating an e-mail profile	36
Canceling an e-mail	36
Understanding e-mail options	36
E-mail server setup	38
Address book setup	38
Faxing	39
Sending a fax	39
Using fax destination shortcuts	40
Using the address book	40
Sending faxes from a computer	40
Creating shortcuts	41
From a computer	41
From the MFP	41
Understanding fax options	42
Changing the fax resolution	43
Adjusting the Darkness setting	43
Sending a fax at a later time	43
Cancel an outgoing fax	44
Fax tips	44
Fax setup	45
FTP	47
Entering the FTP address	47
Using a shortcut number	47
Using the address book	47
Creating shortcuts	48
From a computer	48
From the MFP	48
FTP options	48
FTP tips	50
Scanning to a PC or USB flash memory device	51
Create a scan to PC profile	51
Understanding scan to PC options	52
Scanning to a USB flash memory device	53
Scanning tips	53
Printing	54
Sending a job to print	54
Printing from a USB flash memory device	54
Canceling a print job	56
Canceling a job from the MFP control panel	56
Canceling a job from a computer running Windows	56
Canceling a job from a Macintosh computer	57
Printing the menu settings page	57
Printing a network setup page	57
Printing a font sample list	57
Printing a directory list	58
Printing confidential and held jobs	58
Printing a confidential job	58
Printing and deleting held jobs	59
Printing on specialty media	61
Loading standard trays and optional trays	62
Setting the Paper Type and Paper Size	64
Loading the multipurpose feeder	64
Loading the 2000-sheet drawer	67
Loading the envelope feeder	69
Linking trays	71
Understanding paper and specialty media guidelines	72
Supported print media	72
Selecting print media	76
Paper	76
Transparencies	77
Envelopes	77
Labels	78
Card stock	79
Storing print media	79
Avoiding jams	80
Installing and removing options	81
Installing input options	81
Order of installation	81
Installing a 250-sheet or 500-sheet drawer	82
Installing a duplex unit	83
Installing memory or option cards	84
Accessing the MFP system board	84
Installing or removing a memory card	87
Installation	87
Removal	88
Installing or removing a flash memory or firmware card	89
Installation	89
Removal	90
Installing an optioncard	91
Replacing the shield	92
Maintaining the MFP	93
Storing supplies	93
Determining the status of supplies	94
Conserving supplies	95
Ordering supplies	95
Ordering a print cartridge	95
Ordering a maintenance kit	97
Ordering charge rolls	98
Ordering a transfer roller	98
Ordering pick rollers	98
Ordering an ADF pick mechanism	98
Ordering an ADF separator roller	98
Ordering a label fuser cleaner	98
Recycling Lexmark products	98
Cleaning the scanner glass and backing material	99
Scanner registration	100
Moving the MFP	101
Moving the MFP within the office	101
Preparing the MFP for shipment	101
Clearing jams	102
Identifying jams	102
Access doors and trays	103
Understanding jam messages	103
Clearing jams	104
Clearing ADF Jams	113
Administrative support	114
Adjusting control panel brightness	114
Brightness	114
Restoring factory default settings	114
Adjusting screen timeout	115
Adjusting Power Saver	115
Configuring the MFP	115
Setting Password Protect for the menus	115
Restricting Function Access	116
Preventing access to the menus from the control panel	116
Disabling the Driver to Fax menu item	116
Setting the Device Lockout personal identification number (PIN)	117
Setting a password before printing received faxes	117
Releasing held faxes for printing	117
Setting security using the Embedded Web Server (EWS)	118
Using the secure EWS	118
Supporting SNMPv3 (Simple Network Management Protocol version 3)	118
Supporting IPSec (Internet Protocol Security)	119
Disabling ports and protocols	120
Using 802.1x Authentication	120
Confidential Print Setup	121
Encrypting the hard disk	121
Hard disk wiping	122
Using the restricted server list function	123
Troubleshooting	124
Understanding MFP messages	124
Online technical support	124
Checking an unresponsive MFP	124
Printing multiple language PDFs	125
Solving printing problems	125
Solving copy quality problems	127
Solving scan quality problems	127
Solving fax quality problems	128
Solving option problems	128
Solving 2000-sheet drawer problems	129
Solving paper feed problems	130
Print quality troubleshooting	131
Printing the print defects guide	131
Printing the print quality test pages	131
Solving print quality problems	132
Notices	136
Conventions	136
Electronic emission notices	136
Part 68	139
Other telecommunications notices	140
Notice to users of the Canadian telephone network	140
Notice to users of the New Zealand telephone network	141
South Africa telecommunications notice	141
Using this product in Germany	141
Using this product in Switzerland	141
Noise emission levels	142
ENERGY STAR	143
Waste from Electrical and Electronic Equipment (WEEE) directive	143
Laser advisory label	143
LUOKAN 1 LASERLAITE	143
Laser notice	143

Match case Limit results 1 per page

Selecting print media

Understanding paper and specialty media guidelines

Labels

The MFP can print on many labels designed for use with laser printers. These labels are supplied in letter size, A4 size, and

legal size sheets. Label adhesives, face sheet (printable stock), and topcoats must be able to withstand temperatures of

230°C (446°F) and pressure of 25 pounds per square inch (psi).

Try a sample of any labels you are considering using with the MFP before purchasing a large quantity.

For detailed information on label printing, characteristics, and design, see the

Card Stock & Label Guide

available on the

Lexmark Web site at

www.lexmark.com/publications

Note:

Labels are one of the most difficult print media for laser MFPs. All MFP models require a special fuser

cleaner for label applications to optimize feed reliability. See

Ordering supplies

for information on

obtaining a label fuser cleaner.

After printing approximately 10,000 pages of labels (or each time you replace the print cartridge), complete the following

steps to maintain MFP feeding reliability:

Print five sheets of paper.

Wait approximately five seconds.

Print five more sheets of paper.

When printing on labels:

•

Set the Paper Size/Type menu item to Labels in the Paper menu. You can set the Paper Size/Type from the MFP

control panel, the MFP driver, or from MarkVision.

•

Feed vinyl labels from the standard 250- or 500-sheet trays or the optional 250- or 500-sheet drawers. For vinyl

labels, set the Paper Type to Labels, the Labels Texture to Smooth, and the Label Weight to Heavy, or set the

Paper Type to vinyl labels and the texture and weight to normal.

•

Do not load labels with paper or transparencies in the same source; mixing print media can cause feeding

problems and print quality problems.

•

Do not use label sheets with a slick backing material.

•

Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a jam. Partial sheets

also contaminate the MFP and your cartridge with adhesive, and could void the MFP and cartridge warranties.

•

Use labels that can withstand temperatures of 230°C (446°F) without sealing, excessive curling, wrinkling, or

releasing hazardous emissions.

•

Do not print within 1 mm (0.04 in.) of the edge of the label, of the perforations, or between die-cuts of the label.

•

Do not use label sheets that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive

at least 1 mm (0.04 in.) away from edges. Adhesive material contaminates the MFP and could void the warranty.

•

If zone coating of the adhesive is not possible, a 1.6 mm (0.1 in.) strip should be removed on the leading and

driver edge, and a non-oozing adhesive should be used.

•

Remove a 1.6 mm (0.1 in.) strip from the leading edge to prevent labels from peeling inside the MFP.

•

Portrait orientation is preferred, especially when printing bar codes.

•

Do not use labels that have exposed adhesive.