Netgear DG834G DG834Gv4 Reference Manual - Page 91

VPN Tunnel Configuration, Setting Up a Client-to-Gateway VPN Configuration, VPN Tunnel

Get Netgear DG834G - 54 Mbps Wireless ADSL Firewall Router PDF manuals and user guides
UPC - 606449029918
View all Netgear DG834G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

ADSL2+ Modem Wireless Router DG834G Reference Manual VPN Tunnel Configuration There are two tunnel configurations and three ways to configure them: • Use the VPN Wizard to configure a VPN tunnel (recommended for most situations): - See "Setting Up a Client-to-Gateway VPN Configuration" on page 6-5. - See "Setting Up a Gateway-to-Gateway VPN Configuration" on page 6-18. • See "Using Auto Policy to Configure VPN Tunnels" on page 6-32 when the VPN Wizard and its VPNC defaults (see Table 6-2) are not appropriate for your special circumstances, but you want to automate the Internet Key Exchange (IKE) setup. • See "Using Manual Policy to Configure VPN Tunnels" on page 6-41 when the VPN Wizard and its VPNC defaults (see Table 6-2) are not appropriate for your special circumstances and you must specify each phase of the connection. You manually enter all the authentication and key parameters. You have more control over the process; however, the process is more complex, and there are more opportunities for errors or configuration mismatches between your DG834G v4 and the corresponding VPN endpoint gateway or client workstation. Note: NETGEAR publishes additional interoperability scenarios with various gateway and client software products. Look on the NETGEAR website at www.netgear.com for these interoperability scenarios. Setting Up a Client-to-Gateway VPN Configuration 22.23.24.25 DG834G VPN Tunnel 0.0.0.0 192.168.3.1 PCs Figure 6-3 PC (Running NETGEAR ProSafe VPN Client) Setting up a VPN between a remote PC running the NETGEAR ProSafe VPN Client and a network gateway involves these two steps: Virtual Private Networking 6-5 v2.0, September 2007

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
ADSL2+ Modem Wireless Router DG834G Reference Manual
Virtual Private Networking
6-5
v2.0, September 2007
VPN Tunnel Configuration
There are two tunnel configurations and three ways to configure them:
•
Use the VPN Wizard to configure a VPN tunnel (recommended for most situations):
–
See
“Setting Up a Client-to-Gateway VPN Configuration” on page 6-5
.
–
See
“Setting Up a Gateway-to-Gateway VPN Configuration” on page 6-18
.
•
See
“Using Auto Policy to Configure VPN Tunnels” on page 6-32
when the VPN Wizard and
its VPNC defaults (see
Table 6-2
) are not appropriate for your special circumstances, but you
want to automate the Internet Key Exchange (IKE) setup.
•
See
“Using Manual Policy to Configure VPN Tunnels” on page 6-41
when the VPN Wizard
and its VPNC defaults (see
Table 6-2
) are not appropriate for your special circumstances and
you must specify each phase of the connection. You manually enter all the authentication and
key parameters. You have more control over the process; however, the process is more
complex, and there are more opportunities for errors or configuration mismatches between
your DG834G v4 and the corresponding VPN endpoint gateway or client workstation.
Setting Up a Client-to-Gateway VPN Configuration
Setting up a VPN between a remote PC running the NETGEAR ProSafe VPN Client and a
network gateway involves these two steps:
Note:
NETGEAR publishes additional interoperability scenarios with various
gateway and client software products. Look on the NETGEAR website at
www.netgear.com
for these interoperability scenarios.
Figure 6-3
192.168.3.1
VPN Tunnel
DG834G
22.23.24.25
PC
(Running NETGEAR
ProSafe VPN Client)
PCs
0.0.0.0