Home » Netgear Manuals » Wireless » Netgear DG834G » Manual Viewer

Netgear DG834G DG834Gv4 Reference Manual - Page 92

Step 1: Configuring the Client-to-Gateway VPN Tunnel on the DG834G v4

UPC - 606449029918

Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

ADSL2+ Modem Wireless Router DG834G Reference Manual • "Step 1: Configuring the Client-to-Gateway VPN Tunnel on the DG834G v4" on page 6-6 describes how to use the VPN Wizard to configure the VPN tunnel between the remote PC and network gateway. • "Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC" on page 6-9 shows how to configure the NETGEAR ProSafe VPN Client endpoint. Step 1: Configuring the Client-to-Gateway VPN Tunnel on the DG834G v4 Note: This section uses the VPN Wizard to set up the VPN tunnel using the VPNC default parameters listed in Table 6-2 on page 6-4. If you have special requirements not covered by these VPNC-recommended parameters, refer to "Setting Up VPN Tunnels in Special Circumstances" on page 6-32 to set up the VPN tunnel. The worksheet in Table 6-3 identifies the parameters used in the following procedure. A blank worksheet is at "Planning a VPN". Table 6-3. VPN Tunnel Configuration Worksheet Connection Name: Pre-Shared Key: Secure Association -- Main Mode or Manual Keys: Perfect Forward Secrecy -- Enabled or Disabled: Encryption Protocol -- DES or 3DES: Authentication Protocol -- MD5 or SHA-1: Diffie-Hellman (DH) Group -- Group 1 or Group 2: Key Life in seconds: IKE Life Time in seconds: VPN Endpoint Client DG834G v4 Local IPSec ID toDG834 toClient LAN IP Address - 192.168.3.1 Subnet Mask - 255.255.255.0 RoadWarrior 12345678 Main Disabled 3DES SHA-1 Group 2 28800 (8 hours) 3600 (1 hour) FQDN or Gateway IP (WAN IP Address) Dynamic 22.23.24.25 Follow this procedure to configure a client-to-gateway VPN tunnel using the VPN Wizard. 6-6 Virtual Private Networking v2.0, September 2007

Section	Page
ADSL2+ Modem Wireless Router DG834G Reference Manual	1
Contents	7
About This Manual	13
Conventions, Formats, and Scope	13
How to Use This Manual	14
How to Print this Manual	14
Chapter 1 Configuring Your Internet Connection	17
Using the Setup Manual	17
What You Need Before You Begin	18
Logging In to the Modem Router	18
Auto-Detecting Your Internet Connection	20
Viewing or Manually Configuring Your ISP Settings	22
Understanding the Basic Settings Screen	23
ADSL Settings	26
How the Internet Connection Works	26
Chapter 2 Wireless Configuration	27
Wireless Placement and Range Guidelines	28
Viewing or Changing Wireless Settings	28
Wireless Security	31
Wireless Station Access Control	33
Restricting Access by MAC Address	34
Configuring WEP	35
Configuring WPA	37
Chapter 3 Protecting Your Network	39
Protecting Access to Your ADSL2+ Modem Wireless Router	39
Changing the Built-In Password	39
Changing the Administrator Login Time-out	40
Configuring Basic Firewall Services	40
Blocking Keywords, Sites, and Services	41
Blocking Keywords and Sites	41
Firewall Rules	42
Instant Messaging (IM) Ports	43
Inbound Rules (Port Forwarding)	44
Inbound Rule Example: A Local Public Web Server	44
Inbound Rule Example: Allowing Videoconferencing	45
Considerations for Inbound Rules	46
Outbound Rules (Service Blocking)	46
Outbound Rule Example: Blocking Instant Messenger	46
Order of Precedence for Rules	48
Services	48
Defining Services	49
Setting Times and Scheduling Firewall Services	49
Setting Your Time Zone	50
Scheduling Firewall Services	51
Chapter 4 Managing Your Network	53
Backing Up, Restoring, or Erasing Your Settings	53
Backing Up the Configuration to a File	53
Restoring the Configuration from a File	54
Erasing the Configuration	54
Upgrading the Modem Router Firmware	54
Upgrading the Modem Router Firmware	55
Network Management Information	56
Viewing Modem Router Status and Usage Statistics	56
Viewing Statistics	58
Connection Status	59
Viewing Attached Devices	60
Viewing, Selecting, and Saving Logged Information	61
Selecting Which Information to Log	62
Saving Log Files on a Server	62
Examples of Log Messages	63
Activation and Administration	63
Dropped Packets	63
Enabling Security Event E-mail Notification	64
Running Diagnostic Utilities and Rebooting the Modem Router	65
Enabling Remote Management	66
Configuring Remote Management	66
Chapter 5 Advanced Configuration	69
Advanced Settings	69
WAN Setup	69
Setting Up a Default DMZ Server	71
LAN IP Settings	72
DHCP Settings	74
Use Router as DHCP Server	74
Reserved IP Addresses	75
Dynamic DNS	75
Configuring Dynamic DNS	76
Using Static Routes	77
Static Route Example	77
Configuring Static Routes	78
Universal Plug and Play (UPnP)	79
Wireless Bridging and Repeating	81
Point-to-Point Bridge Configuration	82
Multi-Point Bridge Configuration	83
Repeater with Wireless Client Association	84
Chapter 6 Virtual Private Networking	87
Overview of VPN Configuration	87
Client-to-Gateway VPN Tunnels	88
Gateway-to-Gateway VPN Tunnels	88
Planning a VPN	89
VPN Tunnel Configuration	91
Setting Up a Client-to-Gateway VPN Configuration	91
Step 1: Configuring the Client-to-Gateway VPN Tunnel on the DG834G v4	92
Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC	95
Setting Up a Gateway-to-Gateway VPN Configuration	104
VPN Tunnel Control	111
Activating a VPN Tunnel	111
Using the VPN Status Page to Activate a VPN Tunnel	111
Activating the VPN Tunnel by Pinging the Remote Endpoint	112
Start Using a VPN Tunnel to Activate It	114
Verifying the Status of a VPN Tunnel	114
Deactivating a VPN Tunnel	116
Using the Policy Table on the VPN Policies Screen to Deactivate a VPN Tunnel	116
Using the VPN Status Screen to Deactivate a VPN Tunnel	116
Deleting a VPN Tunnel	117
Setting Up VPN Tunnels in Special Circumstances	118
Using Auto Policy to Configure VPN Tunnels	118
Configuring VPN Network Connection Parameters	119
Example of Using Auto Policy	123
Using Manual Policy to Configure VPN Tunnels	127
Chapter 7 Troubleshooting	131
Basic Functioning	131
Power LED Is Not On	132
Power LED Is Red	132
LAN or DSL or Internet Port LEDs Are Not On	132
Troubleshooting Access to the Modem Router Main Menu	133
Troubleshooting the ISP Connection	134
ADSL Link	134
ADSL Link	134
DSL LED Is Solid Green	134
DSL LED Is Blinking	134
DSL LED Is Off	134
Obtaining a WAN IP Address	135
Troubleshooting PPPoE or PPPoA	136
Troubleshooting Internet Browsing	136
Troubleshooting a TCP/IP Network Using the Ping Utility	137
Testing the LAN Path to Your Router	137
Testing the Path from Your Computer to a Remote Device	138
Restoring the Default Configuration and Password	138
Using the Reset Button	139
Problems with Date and Time	139
Appendix A Technical Specifications	141
Appendix B NETGEAR VPN Configuration	143
DG834G v4 to FVL328	143
Configuration Profile	143
Step-By-Step Configuration	144
DG834G v4 with FQDN to FVL328	148
Configuration Profile	148
Using a Fully Qualified Domain Name (FQDN)	149
Step-By-Step Configuration	149
Configuration Summary (Telecommuter Example)	153
Setting Up the Client-to-Gateway VPN Configuration (Telecommuter Example)	154
Step 1: Configuring the Client-to-Gateway VPN Tunnel on the VPN Router at the Employer’s Main Office	154
Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC at the Telecommuter’s Home Office	156
Monitoring the VPN Tunnel (Telecommuter Example)	164
Viewing the PC Client’s Connection Monitor and Log Viewer	164
Viewing the VPN Router’s VPN Status and Log Information	165