Netgear WBC502 User Manual - Page 46

Click the AP Detection, Under Network, select

Get Netgear WBC502 PDF manuals and user guides View all Netgear WBC502 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Insight Instant AirBridge WBC502 User Manual This setup does not require a line of sight between the access point at the main site and the client bridge. The access point with which the client bridge associates can be either another AirBridge or a different model access point. To configure the AirBridge as a client bridge: 1. Open a web browser from a computer that is connected to the same network as the AirBridge or directly to the AirBridge through an Ethernet cable or WiFi connection. 2. Enter the IP address that is assigned to the AirBridge. The login page displays. If your browser does not display the login page but displays a security message and does not let you proceed, see Log in to the AirBridge after initial setup on page 34. 3. Enter the AirBridge user name and local device password. The user name is admin. The local device password is the one that you specified the first time that you logged in. The user name and password are case-sensitive. If you previously managed the AirBridge through the NETGEAR Insight app or Insight Cloud portal, enter the Insight network password for the Insight network location to which the AirBridge was assigned (see Connect over WiFi using the NETGEAR Insight app on an iOS or Android mobile device on page 15). The Device Status page displays the Device Information section and other sections. 4. Under Network, select Wireless. The Wireless Settings page displays. 5. From the Operation Mode menu, select Client Bridge. Note: For information about optional advanced settings that display on the page, such as changing the Auto RF mode (so that you can set a specific transmission power) and bit rate, see Manage Advanced WiFi and Radio Features on page 90. We recommend that you do not change these advanced settings while you perform the current task. 6. Click the AP Detection Scan button. A new page opens. After the AirBridge completes its scan for neighboring access points, the page displays (for each detected access point) the information that is described in the following table. Manually Configure or Change 46 the Operation Mode User Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
This setup does not require a line of sight between the access point at the main site and
the client bridge. The access point with which the client bridge associates can be either
another AirBridge or a different model access point.
To configure the AirBridge as a client bridge:
1.
Open a web browser from a computer that is connected to the same network as the
AirBridge or directly to the AirBridge through an Ethernet cable or WiFi connection.
2.
Enter the IP address that is assigned to the AirBridge.
The login page displays.
If your browser does not display the login page but displays a security message and
does not let you proceed, see Log
in
to
the
AirBridge
after
initial
setup
on page 34.
3.
Enter the AirBridge user name and local device password.
The user name is
admin
. The local device password is the one that you specified
the first time that you logged in. The user name and password are case-sensitive.
If you previously managed the AirBridge through the NETGEAR Insight app or Insight
Cloud portal, enter the Insight network password for the Insight network location to
which the AirBridge was assigned (see Connect
over
WiFi
using
the
NETGEAR
Insight
app
on
an
iOS
or
Android
mobile
device
on page 15).
The Device Status page displays the Device Information section and other sections.
4.
Under Network, select
Wireless
.
The Wireless Settings page displays.
5.
From the
Operation Mode
menu, select
Client Bridge
.
Note:
For information about optional advanced settings that display on the page,
such as changing the Auto RF mode (so that you can set a specific transmission
power) and bit rate, see Manage
Advanced
WiFi
and
Radio
Features
on page 90.
We recommend that you do not change these advanced settings while you perform
the current task.
6.
Click the AP Detection
Scan
button.
A new page opens. After the AirBridge completes its scan for neighboring access
points, the page displays (for each detected access point) the information that is
described in the following table.
User Manual
46
Manually Configure or Change
the Operation Mode
Insight Instant AirBridge WBC502 User Manual