Sanyo 26KHS72R Installation Instructions - Page 36

Khhs2672r

Get Sanyo 26KHS72R - 25,200 BTU Ductless Single Zone Mini-Split Wall-Mounted Heat Pump PDF manuals and user guides View all Sanyo 26KHS72R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

07-115 SSHP_II 5/7/07 3:59 PM Page 36 KHH(S)2672R Remove and discard the set screws and take off the wall fixture. (Fig. 3-29) KHH(S)2672R (1) Tape the full-scale installation diagram on the wall at the location selected. Make sure the unit is hori- K zontal using a level or tape measure to measure down from the ceiling. (Fig. 3-30) (2) Before drilling a hole, check that there are no studs or pipes behind the determined location. CAUTION Avoid any area where electrical wiring or conduit is located. Also take this precaution if the tubing goes through a wall at any other location. (3) Using a sabre saw, key hole saw or 3-5/32 in. hole-cutting drill attachment, make a hole in the wall. The required minimum hole diameter for these models is 3-3/16 in. (Fig. 3-31) (4) Measure the thickness of the wall from the inside edge to the outside edge and cut PVC pipe at a slight angle 1/4 in. shorter than the thickness of the wall. (Fig. 3-32) (5) Place the plastic cover over the end of the pipe, (for indoor side only) and insert in the wall. (Fig. 3-33) Wall fixture Set screws only for transportation Fig. 3-29 Tape Full-scale installation diagram Fig. 3-30 NOTE Hole should be made at a slight dowward slant to the outdoor side. Indoor side Outdoor side Fig. 3-31 PVC pipe (locally purchased) Cut at slight angle Fig. 3-32 INSIDE Wall Plastic cover OUTSIDE PVC pipe Slight angle Fig. 3-33 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
36
K
Remove and discard the set screws and take off the
wall fixture. (Fig. 3-29)
(1)
Tape the full-scale installation diagram on the wall
at the location selected. Make sure the unit is hori-
zontal using a level or tape measure to measure
down from the ceiling. (Fig. 3-30)
(2)
Before drilling a hole, check that there are no studs
or pipes behind the determined location.
KHH(S)2672R
KHH(S)2672R
CAUTION
Avoid any area where electrical
wiring or conduit is located.
Also take this precaution if the
tubing goes through a wall at
any other location.
Wall fixture
Set screws only for transportation
Fig. 3-29
Tape
m
a
r
g
a
i
d
n
o
i
t
a
l
l
a
t
s
n
i
e
l
a
c
s
-
l
l
u
F
Fig. 3-30
(3)
Using a sabre saw, key hole saw or 3-5/32 in.
hole-cutting drill attachment, make a hole in the
wall. The required minimum hole diameter for
these models is 3-3/16 in. (Fig. 3-31)
(4)
Measure the thickness of the wall from the inside
edge to the outside edge and cut PVC pipe at a
slight angle 1/4 in. shorter than the thickness of
the wall. (Fig. 3-32)
(5)
Place the plastic cover over the end of the pipe,
(for indoor side only) and insert in the wall.
(Fig. 3-33)
Indoor
side
Outdoor
side
Fig. 3-31
Cut at slight angle
PVC pipe (locally purchased)
Fig. 3-32
Plastic
cover
INSIDE
Wall
Slight
angle
PVC pipe
OUTSIDE
Fig. 3-33
NOTE
Hole should be made at a slight dowward slant to the
outdoor side.
07-115 SSHP_II
5/7/07
3:59 PM
Page 36