Sanyo 26KHS72R Installation Instructions - Page 84

remote controller address connector on the PCB from main

Get Sanyo 26KHS72R - 25,200 BTU Ductless Single Zone Mini-Split Wall-Mounted Heat Pump PDF manuals and user guides View all Sanyo 26KHS72R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 84 highlights

07-115 SSHP_II 5/7/07 4:00 PM Page 84 7-23. When Setting Indoor Unit Control PCB Switch for Wall-Mounted Indoor Unit When using either the wired or wireless remote controller, refer to the tables below and accordingly slide the switch on the indoor unit control PCB. G If this setting is not made correctly an alarm will occur. (The operation lamp on the display blinks.) G This setting is not necessary if both the wired remote controller and wireless remote controller are used. However, when you use indoor unit KHS type, set the wired remote controller address connector on the PCB from main to sub position. Wired remote controller G The slide switch setting at the time of factory shipment for model KH type is "A", and for model KHS type is "B." Remote controller address connector Main RCU check Sub RCU. ADR G KH(S)3072 / 3672R, KHH(S)2672R When using wrired A remote controller Nos. 1, 2 OFF, No. 3 ON RC (WL) When using wireless B remote controller Nos. 1, 2, 3 all OFF G KH(S)2672R When using wired A remote controller Nos. 1, 2 OFF, No. 3 ON. When using wireless B remote controller Nos. 1, 2, 3 all OFF 84

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
84
RC
(WL)
7-23.
When Setting Indoor Unit Control PCB Switch for Wall-Mounted Indoor Unit
When using either the wired or wireless remote controller, refer to the tables below and accordingly slide the switch on
the indoor unit control PCB.
●
If this setting is not made correctly an alarm will occur. (The operation lamp on the display blinks.)
●
This setting is not necessary if both the wired remote controller
and wireless remote controller are used.
However, when you use indoor unit KHS type, set the wired
remote controller address connector on the PCB from main to
sub position.
●
The slide switch setting at the time of factory shipment for
model KH type is “A”, and for model KHS type is “B.”
●
KH(S)3072 / 3672R, KHH(S)2672R
A
Nos. 1, 2 OFF, No. 3 ON
B
Nos. 1, 2, 3 all OFF
When using
wireless
remote
controller
When using
wrired
remote
controller
A
Nos. 1, 2 OFF, No. 3 ON.
B
Nos. 1, 2, 3 all OFF
When using
wireless
remote
controller
When using
wired
remote
controller
●
KH(S)2672R
Wired remote co
n
troller
addre
ss
co
nn
ector
RCU. ADR
Mai
n
Su
b
RCU check
Remote co
n
troller
07-115 SSHP_II
5/7/07
4:00 PM
Page 84