Sanyo 26KHS72R Installation Instructions - Page 38

a If Wooden Wall, b If the Wall is Brick, Concrete or Similar, Fig. 3-38, Fig. 3-39

Get Sanyo 26KHS72R - 25,200 BTU Ductless Single Zone Mini-Split Wall-Mounted Heat Pump PDF manuals and user guides View all Sanyo 26KHS72R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

07-115 SSHP_II 5/7/07 3:59 PM Page 38 KHH(S)2672R Confirm that the wall is strong enough to support the unit. a) If Wooden Wall (1) Attach the wall fixture to the wall with the 9 screws provided. (Fig. 3-38) If you are not able to line up the holes in the wall K fixture with the beam locations marked on the wall, use rawl plugs or toggle bolts to go through the holes on the panel or drill 13/64 in. dia. holes in the panel over the stud locations and then mount the wall fixture. (2) Check with a tape measure or carpenter's level that the wall fixture is level. This is important so that the unit is correctly installed. (3) Make sure the wall fixture is flush against the wall. Any space between the wall and unit will cause noise and vibration. b) If the Wall is Brick, Concrete or Similar Drill 3/16 in. dia. holes in the wall. Insert rawl plugs for appropriate mounting screws. (Fig. 3-39) wall fixture Fig. 3-38 3/16 in. dia. hole Rawl plug Fig. 3-39 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
38
K
Confirm that the wall is strong enough to support the
unit.
a) If Wooden Wall
(1)
Attach the wall fixture to the wall with the 9 screws
provided. (Fig. 3-38)
If you are not able to line up the holes in the wall
fixture with the beam locations marked on the wall,
use rawl plugs or toggle bolts to go through the
holes on the panel or drill 13/64 in. dia. holes in the
panel over the stud locations and then mount the
wall fixture.
(2)
Check with a tape measure or carpenter’s level
that the wall fixture is level. This is important so
that the unit is correctly installed.
(3)
Make sure the wall fixture is flush against the wall.
Any space between the wall and unit will cause
noise and vibration.
b) If the Wall is Brick, Concrete or Similar
Drill 3/16 in. dia. holes in the wall. Insert rawl plugs for
appropriate mounting screws. (Fig. 3-39)
KHH(S)2672R
wall fixture
Fig. 3-38
3/16 in.
dia. hole
Rawl plug
Fig. 3-39
07-115 SSHP_II
5/7/07
3:59 PM
Page 38