Sanyo 26KHS72R Installation Instructions - Page 43

Wiring Instructions for Inter-Unit Connections, How to remove the cover plate, Fig. 3-57, Fig. 3-58a

Get Sanyo 26KHS72R - 25,200 BTU Ductless Single Zone Mini-Split Wall-Mounted Heat Pump PDF manuals and user guides View all Sanyo 26KHS72R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

07-115 SSHP_II 5/7/07 4:00 PM Page 43 3-16. Wiring Instructions for Inter-Unit Connections KH(S)2672R Rear Wall panel (1) Insert the inter-unit wiring (according to local electrical codes) into the through-the-wall PVC pipe. Run the wiring toward the indoor side allowing approx. 10 inches to extend from the wall face. (Fig. 3-57) Wiring Plastic cover (2) Route the inter-unit wiring from the back of the indoor unit and pull it toward the front for connection. (Figs. 3-58a and 3-58b) K 10 in. Fig. 3-57 (3) Connect the inter-unit wiring to the corresponding terminals on the terminal plate (Figs. 3-58a and 3-58b) while referring to the wiring diagram. Terminal plate (4) Be sure to secure the wiring with the provided clamp. How to remove the cover plate To access the terminal plate inside the indoor unit, follow these steps. (1) Using a Phillips screwdriver, remove the screw on the cover plate. (Figs. 3-58a and 3-58b) Cover plate (2) Remove the cover plate. Fig. 3-58a Earth plate Inter-unit control line wiring Lock nut Top of conduit connector Fig. 3-58b 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
43
K
3-16.
Wiring Instructions for Inter-Unit Connections
(1)
Insert the inter-unit wiring (according to local
electrical codes) into the through-the-wall PVC
pipe. Run the wiring toward the indoor side allowing
approx. 10 inches to extend from the wall face.
(Fig. 3-57)
(2)
Route the inter-unit wiring from the back of the
indoor unit and pull it toward the front for
connection. (Figs. 3-58a and 3-58b)
(3)
Connect the inter-unit wiring to the corresponding
terminals on the terminal plate (Figs. 3-58a and
3-58b) while referring to the wiring diagram.
(4)
Be sure to secure the wiring with the provided
clamp.
How to remove the cover plate
To access the terminal plate inside the indoor unit,
follow these steps.
(1)
Using a Phillips screwdriver, remove the screw on
the cover plate. (Figs. 3-58a and 3-58b)
(2)
Remove the cover plate.
KH(S)2672R
Rear
panel
Wiring
Wall
10 in.
Plastic
cover
Fig. 3-57
Terminal
plate
Cover plate
Fig. 3-58a
Lock
nu
t
Top of co
n
d
u
it
co
nn
ector
I
n
ter-
un
it
co
n
trol li
n
e
wiri
ng
Earth
plate
Fig. 3-58b
07-115 SSHP_II
5/7/07
4:00 PM
Page 43