Sanyo 26KHS72R Installation Instructions - Page 80

le Remote Controller

Get Sanyo 26KHS72R - 25,200 BTU Ductless Single Zone Mini-Split Wall-Mounted Heat Pump PDF manuals and user guides View all Sanyo 26KHS72R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

07-115 SSHP_II 5/7/07 4:00 PM Page 80 7-18. Wiring System Diagram for Multiple Remote Controllers When installing multiple remote controllers This multiple system is used for operating the unit(s) at different positions. (A maximum of 2 signal receiving units can be installed.) Setting method To execute this control, make the setting according to the following procedure. (1) Of the two installed signal receiving units, make one the main signal receiving unit (factoryshipped state). (2) On the other signal receiving unit, change the address connector on the PCB from main to sub position. In this state, it functions as a sub-signal receiving unit. RC (WL) Basic wiring diagram CAUTION Carry out the wiring correctly (incorrect wiring will damage the equipment). To operate 1 indoor unit with 2 signal receiving units set at different locations. Signal receiving unit (main) (sub) (Option) 12 12 Remote control Connection wiring cable terminal 1 2 board Indoor unit Earth 80

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
80
RC
(WL)
7-1
8
. Wirin
g
S
y
s
tem Dia
g
ram for Multi
p
le Remote Controller
s
When in
s
tallin
g
multi
p
le remote controller
s
Thi
s
m
u
ltiple
s
y
s
tem i
s
us
ed for operati
ng
the
un
it(
s
) at
differe
n
t po
s
itio
ns
. (A maxim
u
m of 2
s
i
gn
al receivi
ng
un
it
s
ca
n
be i
ns
talled.)
S
ettin
g
method
To exec
u
te thi
s
co
n
trol, make the
s
etti
ng
accordi
ng
to the followi
ng
proced
u
re.
(1)
Of the two i
ns
talled
s
i
gn
al receivi
ng
un
it
s
, make
o
n
e the mai
n
s
i
gn
al receivi
ng
un
it (factory-
s
hipped
s
tate).
(2)
O
n
the other
s
i
gn
al receivi
ng
un
it, cha
ng
e the
addre
ss
co
nn
ector o
n
the PCB from mai
n
to
su
b
po
s
itio
n
.
I
n
thi
s
s
tate, it f
un
ctio
ns
a
s
a
su
b-
s
i
gn
al receivi
ng
un
it.
Ba
s
ic wirin
g
dia
g
ram
Carry out the wirin
g
correctly
(incorrect wirin
g
will dama
g
e
the e
q
ui
p
ment).
To operate 1 i
n
door
un
it with 2
s
i
gn
al receivi
ng
un
it
s
s
et at differe
n
t locatio
ns
.
CAUTION
Co
nn
ectio
n
wiri
ng
S
i
gn
al receivi
ng
un
it
12
I
n
door
un
it
Earth
(
su
b)
(mai
n
)
12
(Optio
n
)
12
Remote co
n
trol
cable termi
n
al
board
07-115 SSHP_II
5/7/07
4:00 PM
Page 80