Sanyo 26KHS72R Installation Instructions - Page 62

Basic Wiring Diagram, Wiring procedure, Carry out wiring correctly, incorrect wiring will damage,

Get Sanyo 26KHS72R - 25,200 BTU Ductless Single Zone Mini-Split Wall-Mounted Heat Pump PDF manuals and user guides View all Sanyo 26KHS72R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

07-115 SSHP_II 5/7/07 4:00 PM Page 62 6-3. Basic Wiring Diagram 3/32 4-23/32 CAUTION Carry out wiring correctly (incorrect wiring will damage the equipment). Use shielded wires for inter-unit control wiring and ground the shield on both sides. (Fig. 6-5) Otherwise misoperation because of noise may occur. I Wiring procedure RC (WD) Install the wiring according to the above wiring diagram. G Address setting is automatically executed after turning on the system. An indoor unit address is assigned to each indoor unit. G Operation takes place successively at intervals of 1 second, by using combinations of the address setting of each unit. Shielded wire Ground Fig. 6-5 Ground I Diagram of outer dimensions 5/32 4-23/32 5/8 Unit: inch 62

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
62
RC
(WD)
6-3.
Basic Wiring Diagram
Use shielded wires for inter-unit control wiring and
ground the shield on both sides. (Fig. 6-5)
Otherwise misoperation because of noise may occur.
■
Wiring procedure
Install the wiring according to the above wiring diagram.
●
Address setting is automatically executed after turn-
ing on the system.
An indoor unit address is assigned to each indoor
unit.
●
Operation takes place successively at intervals of 1
second, by using combinations of the address setting
of each unit.
CAUTION
Carry out wiring correctly
(incorrect wiring will damage
the equipment).
■
Diagram of outer dimensions
5/32
4-23/32
5/8
2
3
/
3
2
3
/
3
2
-
4
Fig. 6-5
S
hielded wire
Gro
un
d
Gro
un
d
Unit: inch
07-115 SSHP_II
5/7/07
4:00 PM
Page 62