Sanyo 26KHS72R Installation Instructions - Page 44

Khhs2672r, Khs3072r, Khs3672r

Get Sanyo 26KHS72R - 25,200 BTU Ductless Single Zone Mini-Split Wall-Mounted Heat Pump PDF manuals and user guides View all Sanyo 26KHS72R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

07-115 SSHP_II 5/7/07 4:00 PM Page 44 (1) Insert the inter-unit wiring (according to local codes) into the through-the-wall PVC pipe. Run the wiring toward the indoor side allowing approx. 5" to extend from the wall face. (Figs. 3-59a and 3-59b) Never fix the wiring by any CAUTION means before the indoor unit is fully seated on the rear panel. K (2) Remove the side cover and the metallic cover. (Fig. 3-60 or 3-61, depending on model.) (3) Secure the conduit connector to the chassis with a lock nut. (Fig. 3-60 or 3-61) (4) Give some play to the inter-unit wiring from the outdoor unit to the corresponding terminals on the terminal plate. CAUTION G Be sure to refer to the wiring system diagram label inside the metallic cover and carry out the correct field wiring. Wrong wiring can cause the unit to malfunction. G Check local electrical codes and any specified wiring instructions or limitations. (5) Secure the metallic cover with its screw. Then replace the side cover. KHH(S)2672R KHH(S)2672R Rear panel Wiring Wall Plastic cover 5" Fig. 3-59a KH(S)3072R, KH(S)3672R Wall fixture Wall Connector Wiring 5" Fig. 3-59b KH(S)3072R, KH(S)3672R Lock nut Metallic cover Plastic cover Power line Look nut Elbow conduit Grounding line Fig. 3-60 Screw Metallic cover Lock nut Connector Side cover Fig. 3-61 44

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
Wall
Plastic
cover
Rear
panel
Wiring
5"
Wall
Wall fixture
Connector
Wiring
5"
44
K
(1)
Insert the inter-unit wiring (according to local
codes) into the through-the-wall PVC pipe. Run the
wiring toward the indoor side allowing approx. 5" to
extend from the wall face.
(Figs. 3-59a and 3-59b)
KHH(S)2672R
CAUTION
Never fix the wiring by any
means before the indoor unit is
fully seated on the rear panel.
(2)
Remove the side cover and the metallic cover.
(Fig. 3-60 or 3-61, depending on model.)
(3)
Secure the conduit connector to the chassis with a
lock nut. (Fig. 3-60 or 3-61)
(4)
Give some play to the inter-unit wiring from the
outdoor unit to the corresponding terminals on the
terminal plate.
(5)
Secure the metallic cover with its screw. Then
replace the side cover.
CAUTION
●
Be sure to refer to the wiring
system diagram label inside
the metallic cover and carry
out the correct field wiring.
Wrong wiring can cause the
unit to malfunction.
●
Check local electrical codes
and any specified wiring
instructions or limitations.
KH(S)3072R, KH(S)3672R
Fig. 3-59b
Grounding
line
Power line
Screw
Plastic cover
Metallic cover
Lock
nut
Elbow
conduit
Look nut
Lock
nut
Connector
Metallic cover
Side cover
Fig. 3-60
Fig. 3-61
KH(S)3072R, KH(S)3672R
KHH(S)2672R
Fig. 3-59a
07-115 SSHP_II
5/7/07
4:00 PM
Page 44