Sony HDWS280 Product Manual (Operation Manual 1st Edition (Revised 5)) - Page 75

75

Items in the Extended Setup Menu

Chapter 9

Setup Menus

a) Not applicable in 24PsF/23.98PsF mode

When you set setup menu items 715 through 718, 721, and

740 through 747, set VID.PROC on the P1 PROCS page of

the function menu to MENU. Then the video output control

function on the front panel is disabled.

Items 800 to 899: Settings for audio control

740

MASTER LEVEL (HD)

Adjust the high-definition video signal output from the HD SDI OUTPUT connector.

This adjusts the Y, PB, and PR levels simultaneously.

0.0% (0H) to [100% (800H)] to 141.3% (B4EH)

741

Y LEVEL (HD)

Adjust the Y level of the high-definition video signal output from the HD SDI OUTPUT

connector.

0.0% (0H) to [100% (800H)] to 141.3% (B4EH)

742

PB LEVEL (HD)

Adjust the PB level of the high-definition video signal output from the HD SDI OUTPUT

connector.

0.0% (0H) to [100% (800H)] to 141.3% (B4EH)

743

PR LEVEL (HD)

Adjust the PR level of the high-definition video signal output from the HD SDI OUTPUT

connector.

0.0% (0H) to [100% (800H)] to 141.3% (B4EH)

745

SETUP (BLACK) LEVEL

(HD)

Adjust the setup level of the high-definition video signal output from the HD SDI

OUTPUT connector.

0 to [110H] to 220H

746

SYNC PHASE (HD)

Control the H sync phase of the high-definition video signal output from the HD SDI

OUTPUT connector according to the menu.

0 to [80H] to FFH

747

FINE (HD)

Fine control the H sync phase of the high-definition video signal output from the HD SDI

OUTPUT connector according to the menu.

[0] to 3FFH

Item

number

Item name

Settings

Note

Item

number

Item name

Settings

802

DIGITAL AUDIO MUTING

IN SHUTTLE MODE

Set the digital audio muting conditions during shuttle playback.

[OFF]:

Not muted.

CUEUP:

Muted during cue-up or preroll operations.

FULL:

Muted in shuttle mode.

SLOW:

Muted, with the speed less than

±

0.2 time normal playback.

807

AUDIO OUTPUT PHASE

Select the output timing of digital audio playback signals (HD SDI, and SDI only). The

reference position corresponds to a setting for 80H; when the setting is less than 80H,

the output timing is advanced, and when it is higher than 80H, the output timing is

delayed. (at 80H, 128 samples = approx. 2.7 ms, and 1 sample=approx. 20 μs)

0 to [80] to FF:

Setting in this range

808

INTERNAL AUDIO SIGNAL

GENERATOR

Select the operation of the internal audio test signal generator.

OFF:

No operation

SILNC:

Silent signal

[1KHZ]:

At 1 kHz,

−

20 dB FS sine wave is supplied to all audio input channels.

Note

If the system frequency is set to 23.98PsF or 24 PsF, the frequency 1kHz is 4% lower.

810

AUDIO EDIT PREVIEW

SWITCHER

Set the output phase for the audio playback signal when ASSEMBLE is set to ON.

[INT]:

The audio playback signal output phase is the same as the output phase in E-E

mode. Use this setting when editing with a single VTR, or when previewing while

watching the VTR output signal.

EXT:

The audio playback signal output phase is the same as the phase of an input

video signal or external reference video signal.

Section	Page
Table of Contents	6
Overview	10
1-1 Features	10
1-2 System Configurations	11
1-3 Using the CD-ROM Manual	12
1-3-1 Preparations	12
1-3-2 Reading the CD-ROM Manual	12
Names and Functions of Parts	13
2-1 Front Panel	13
2-1-1 Menu Operation Section	14
2-1-2 Tape Transport Section	15
2-1-3 Display Window	16
2-2 Rear Panel	20
Preparations	22
3-1 Preparing Power Sources	22
3-1-1 Supplying Power	22
3-1-2 Using the Battery Pack	23
3-2 Using a Stand	24
3-3 Connections	25
3-4 Handling Cassettes	26
3-4-1 Usable Cassettes	26
3-4-2 Loading/Ejecting Cassettes	26
3-4-3 Preventing Accidental Erasures	26
3-5 Setting Reference Video Signals	27
3-6 Setting Timecode	28
3-6-1 Setting an Initial Value and Recording Timecode	28
3-6-2 Synchronizing the Internal Timecode Generator with an External Signal	29
3-6-3 Synchronizing the Internal Timecode Generator with a Playback Timecode - Timecode Recording during Auto Editing	30
3-6-4 Converting Timecode in 24- or 25-Frame Mode Playback (TC CONV)	30
3-7 Basic Operations of the Function Menu	31
3-7-1 Configuration of the Function Menu	31
3-7-2 Function Menu Item List	32
3-7-3 Basic Operations	35
3-8 Superimposed Character Information	36
3-9 Using a \	38
3-9-1 Notes on \	38
Recording and Playback	40
4-1 Recording	40
4-1-1 Preparations for Recording	40
4-1-2 Recording Operation	40
4-2 Back Space Editing	41
4-3 Sequential Recording	41
4-4 Playback	43
4-4-1 Preparations for Playback	43
4-4-2 Playback Operation	43
4-4-3 Jog/Shuttle Mode playback	44
Assemble Editing	45
5-1 Overview	45
5-1-1 Assemble Editing	45
5-2 Automatic Editing	45
5-2-1 Setting the Edit Points	45
5-2-2 Modifying and Deleting Edit Points	46
5-2-3 Cueing up to Edit Points and Prerolling	47
5-2-4 Preview	48
5-2-5 Performing Automatic Editing	49
5-2-6 First Edit Function	50
Shot Mark/Shot Data	51
6-1 Overview	51
6-1-1 Shot Mark/Shot Data Function Features	51
Stop Code	52
7-1 Stop Code	52
7-2 Stop Code Operation	52
7-2-1 Detecting the Stop Code	52
7-2-2 Recording the Stop Code	53
7-2-3 Erasing the Stop Code	54
UMID Functions	55
8-1 Overview of UMID Functions	55
8-2 Recording UMIDs	55
8-3 UMID Output and Display	58
8-3-1 UMID Output Settings	58
8-3-2 UMID Display	58
Setup Menus	60
9-1 Setup Menu Configuration	60
9-2 Setup Menu Operations	60
9-2-1 Displaying Setup Menus	60
9-2-2 Setting Setup Menu	61
9-2-3 Menu Bank Operations (menu items B01 to B12)	62
9-3 Items in the Basic Setup Menu	63
9-4 Items in the Extended Setup Menu	66
Maintenance and Inspection	79
10-1 Removing a Cassette When Tape Slack Occurs	79
10-2 Head Cleaning	79
10-3 Error Messages	80
10-4 Warning Messages	82
10-5 Moisture Condensation	83
10-6 Regular Checks	83
10-6-1 Digital Hours Meter	83
10-6-2 Maintenance Timings	84
10-7 LCD Monitor	85
Appendixes	86
Specifications	86

Sony HDWS280 Product Manual (Operation Manual 1st Edition (Revised 5)) - Page 75

% 0H to [100% 800H] to 141.3% B4EH

Page 75 highlights