Sony STR-DN2010 Operating Instructions (Large File - 11.22 MB) - Page 111

Crossover Freq Speaker, crossover frequency, Test Tone, To output test tone from each, speaker

Get Sony STR-DN2010 - Audio Video Receiver PDF manuals and user guides
UPC - 027242779938
View all Sony STR-DN2010 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 111 highlights

3 Press V/v repeatedly to set the size of the selected speaker, then press . • Large If you connect large speakers that will effectively reproduce bass frequencies, select "Large". Normally, select "Large". • Small If the sound is distorted, or you feel a lack of surround effects when using multi channel surround sound, select "Small" to activate the bass redirection circuitry and output the bass frequencies of each channel from the subwoofer or other "Large" speakers. Note This function does not work when "A. DIRECT" is being used. Tips • The "Large" and "Small" settings for each speaker determine whether the internal sound processor will cut the bass signal from that channel. When the bass is cut from a channel, the bass redirection circuitry sends the corresponding bass frequencies to the subwoofer or other "Large" speakers. However, since bass sound has a certain amount of directionality, it is best not to cut it, if possible. Therefore, even when using small speakers, you can set them to "Large" if you want to output the bass frequencies from that speaker. On the other hand, if you are using a large speaker, but prefer not to have bass frequencies output from that speaker, set it to "Small". If the overall sound level is lower than you prefer, set all speakers to "Large". If there is not enough bass, you can use the equalizer to boost the bass levels. • The surround back speakers will be set to the same setting as that of the surround speakers. • When the front speakers are set to "Small", the center, surround, and front high speakers are also automatically set to "Small". • If you do not use the subwoofer, the front speakers are automatically set to "Large". Crossover Freq (Speaker crossover frequency) Lets you set the bass crossover frequency of speakers that the speaker size has been set to "Small" in the Speaker Settings menu. Measured speaker crossover frequency is set for each speaker after the Auto Calibration. 1 Press V/v repeatedly to select the speaker on the screen you want to adjust, then press . 2 Press V/v repeatedly to adjust the value, then press . Test Tone You can select the test tone type on the "Test Tone" screen. Note Test tone is not output from the headphones connected to the S-AIR surround amplifier. Tips • To adjust the level of all speakers at the same time, press MASTER VOL +/- (RM-AAP055 only) or 2 +/- (RM-AAP056 only). You can also use MASTER VOLUME on the receiver. • The adjusted value is shown on the TV screen during adjustment. To output test tone from each speaker You can output test tone from the speakers in sequence. 1 Press B/b repeatedly to select "Test Tone", then press . Adjusting Settings continued 111GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
111
GB
Adjusting Settings
3
Press
V
/
v
repeatedly to set the size of
the selected speaker, then press
• Large
If you connect large speakers that will
effectively reproduce bass frequencies,
select “Large”. Normally, select “Large”.
• Small
If the sound is distorted, or you feel a lack
of surround effects when using multi
channel surround sound, select “Small” to
activate the bass redirection circuitry and
output the bass frequencies of each
channel from the subwoofer or other
“Large” speakers.
Note
This function does not work when “A. DIRECT” is
being used.
Tips
• The “Large” and “Small” settings for each speaker
determine whether the internal sound processor
will cut the bass signal from that channel.
When the bass is cut from a channel, the bass
redirection circuitry sends the corresponding bass
frequencies to the subwoofer or other “Large”
speakers.
However, since bass sound has a certain amount of
directionality, it is best not to cut it, if possible.
Therefore, even when using small speakers, you
can set them to “Large” if you want to output the
bass frequencies from that speaker. On the other
hand, if you are using a large speaker, but prefer
not to have bass frequencies output from that
speaker, set it to “Small”.
If the overall sound level is lower than you prefer,
set all speakers to “Large”. If there is not enough
bass, you can use the equalizer to boost the bass
levels.
• The surround back speakers will be set to the same
setting as that of the surround speakers.
• When the front speakers are set to “Small”, the
center, surround, and front high speakers are also
automatically set to “Small”.
• If you do not use the subwoofer, the front speakers
are automatically set to “Large”.
Lets you set the bass crossover frequency of
speakers that the speaker size has been set to
“Small” in the Speaker Settings menu.
Measured speaker crossover frequency is set
for each speaker after the Auto Calibration.
1
Press
V
/
v
repeatedly to select
the speaker on the screen you
want to adjust, then press
.
2
Press
V
/
v
repeatedly to adjust
the value, then press
.
You can select the test tone type on the “Test
Tone” screen.
Note
Test tone is not output from the headphones
connected to the S-AIR surround amplifier.
Tips
• To adjust the level of all speakers at the same time,
press MASTER VOL +/– (RM-AAP055 only) or
2
+/– (RM-AAP056 only). You can also use
MASTER VOLUME on the receiver.
• The adjusted value is shown on the TV screen
during adjustment.
To output test tone from each
speaker
You can output test tone from the speakers in
sequence.
1
Press
B
/
b
repeatedly to select “Test
Tone”, then press
Crossover Freq (Speaker
crossover frequency)
Test Tone
continued