Toshiba Tecra A3-S711 User Manual - Page 129

Installing the battery pack, Power-up modes

Get Toshiba Tecra A3-S711 PDF manuals and user guides View all Toshiba Tecra A3-S711 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 129 highlights

Power System Installing the battery pack To install a battery pack, follow the steps below. The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. 1. Turn the computer's power off. 2. Disconnect all cables connected to the computer. 3. Hold the battery pack so that the label faces down and the connectors on the battery face the connectors on the computer. 4. Gently press the battery into the battery bay until the latch clicks into place. 5. Lock the Battery Pack Lock and Battery Pack Release Latch to secure the installation. 2 2 1 Installing the battery pack 1 Battery Power-up modes The computer has three power-up modes: ■ Hibernation (saves data in memory to the hard disk) ■ Standby (Power remains on, saving data in RAM, but the CPU and all other devices enter sleep mode.) ■ Boot (does not save data in memory) Refer also to the section Turning off the power in Chapter 3, Getting Started. TECRA A3/S2 6-12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
TECRA A3/S2
6-12
Power System
Installing the battery pack
To install a battery pack, follow the steps below.
1.
Turn the computer's power off.
2.
Disconnect all cables connected to the computer.
3.
Hold the battery pack so that the label faces down and the connectors
on the battery face the connectors on the computer.
4.
Gently press the battery into the battery bay until the latch clicks into
place.
5.
Lock the Battery Pack Lock and Battery Pack Release Latch to secure
the installation.
Installing the battery pack
Power-up modes
The computer has three power-up modes:
■
Hibernation (saves data in memory to the hard disk)
■
Standby (Power remains on, saving data in RAM, but the CPU and all
other devices enter sleep mode.)
■
Boot (does not save data in memory)
The battery pack is a lithium ion battery, which can explode if not properly
replaced, used, handled or disposed of. Dispose of the battery as required
by local ordinances or regulations. Use only batteries recommended by
TOSHIBA as replacements.
1
2
2
1
Battery
Refer also to the section Turning off the power in Chapter 3, Getting Started.