Yamaha RXV1800 Owner's Manual - Page 118

Adjusting the balance of the speaker, level in Zone 2 or Zone 3

Get Yamaha RXV1800 - AV Receiver PDF manuals and user guides
UPC - 027108928463
View all Yamaha RXV1800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 118 highlights

Using multi-zone configuration Operate the following operations after activating the Zone 2 or Zone 3 operation mode. ■ Selecting the input source of Zone 2 or Zone 3 Rotate the CINPUT selector on the front panel (or set the operation mode selector to CAMP and then press one of the input selector buttons on the remote control) to select the input source of the selected zone. If the remote control is used to select the input source, "2: name of the selected input source" or "3: name of the selected input source" is displayed in the display window (A) on the remote control when Zone 2 or Zone 3 is selected respectively. • Select "TUNER" as the input source to use the FM/AM tuning features in the selected zone. For details about the FM/AM tuning operations, see "FM/AM tuning" on page 54. • Select "XM" as the input source to use the XM Satellite Radio features in the selected zone. For details about the XM Satellite Radio operations, see "XM™ Satellite Radio tuning" on page 58. • Select "V-AUX" as the input source to play back the sources in the iPod stationed in a Yamaha iPod universal dock (such as the YDS-10 sold separately) in the selected zone. You can only control iPod in the simple remote mode (see page 64). Note The input sources are shared across all zones. You cannot select the same input source in multiple zones simultaneously. y You must complete this step within 10 seconds while the selected zone flashes in the front panel display. Otherwise, the currently selected zone mode is automatically canceled. In this case, press PZONE CONTROLS on the front panel again. ■ Adjusting the volume level of Zone 2 or Zone 3 ■ Adjusting the balance of the speaker level in Zone 2 or Zone 3 Press ETONE CONTROL repeatedly to select "BALANCE" and then rotate NPROGRAM on the front panel to adjust the balance of the front left and right speaker level of the selected zone. ■ Adjusting the tonal quality of Zone 2 or Zone 3 Set the operation mode selector to CAMP and then press CH +/- on the remote control to adjust the high-frequency response (TREBLE) or TV VOL +/- to adjust the low-frequency response (BASS) respectively. AMP SOURCE TV + TV VOL - BASS + CH - TREBLE y You can also adjust the tonal quality of Zone 2 or Zone 3 by using ETONE CONTROL on the front panel. For details, see "Adjusting the tonal quality" on page 52. Note Check that "ZONE 2" or "ZONE 3" is displayed in the display window (A) of the remote control before you adjust the tonal quality of the corresponding zone (see page 113). Rotate QVOLUME on the front panel (or press BVOLUME +/- on the remote control) to adjust the volume level of the selected zone. y Press DMUTE on the remote control to mute the sound output to the selected zone. Note When you use the external amplifiers in Zone 2 or Zone 3, BVOLUME +/- can be used only when "VOLUME" is set to "VAR" in "ZONE SET" (see page 95). 114 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
114
En
Using multi-zone configuration
■
Selecting the input source of Zone 2 or
Zone 3
Rotate the
C
INPUT
selector on the front panel
(or set the operation mode selector to
C
AMP
and then press one of the input selector buttons
on the remote control) to select the input source
of the selected zone.
If the remote control is used to select the input source, “2:
name of the selected input source” or “3: name of the
selected input source” is displayed in the display window
(
A
) on the remote control when Zone 2 or Zone 3 is
selected respectively.
•
Select “TUNER” as the input source to use the FM/AM
tuning features in the selected zone. For details about
the FM/AM tuning operations, see “FM/AM tuning”
on page 54.
•
Select “XM” as the input source to use the XM
Satellite Radio features in the selected zone. For details
about the XM Satellite Radio operations, see “XM™
Satellite Radio tuning” on page 58.
•
Select “V-AUX” as the input source to play back the
sources in the iPod stationed in a Yamaha iPod
universal dock (such as the YDS-10 sold separately) in
the selected zone. You can only control iPod in the
simple remote mode (see page 64).
The input sources are shared across all zones. You cannot select
the same input source in multiple zones simultaneously.
y
You must complete this step within 10 seconds while the selected
zone flashes in the front panel display. Otherwise, the currently
selected zone mode is automatically canceled. In this case, press
P
ZONE CONTROLS
on the front panel again.
■
Adjusting the volume level of Zone 2 or
Zone 3
Rotate
Q
VOLUME
on the front panel (or press
B
VOLUME +/–
on the remote control) to adjust
the volume level of the selected zone.
y
Press
D
MUTE
on the remote control to mute the sound output to
the selected zone.
When you use the external amplifiers in Zone 2 or Zone 3,
B
VOLUME +/–
can be used only when “VOLUME” is set to
“VAR” in “ZONE SET” (see page 95).
■
Adjusting the balance of the speaker
level in Zone 2 or Zone 3
Press
E
TONE CONTROL
repeatedly to select
“BALANCE” and then rotate
N
PROGRAM
on
the front panel to adjust the balance of the front
left and right speaker level of the selected zone.
■
Adjusting the tonal quality of Zone 2 or
Zone 3
Set the operation mode selector to
C
AMP
and
then press
CH +/–
on the remote control to
adjust the high-frequency response (TREBLE) or
TV VOL +/–
to adjust the low-frequency
response (BASS) respectively.
y
You can also adjust the tonal quality of Zone 2 or Zone 3 by using
E
TONE CONTROL
on the front panel. For details, see
“Adjusting the tonal quality” on page 52.
Check that “ZONE 2” or “ZONE 3” is displayed in the display
window (
A
) of the remote control before you adjust the tonal
quality of the corresponding zone (see page 113).
Operate the following operations after activating the Zone 2
or Zone 3 operation mode.
Note
Note
Note
–
+
TV VOL
+
–
CH
TV
SOURCE
AMP
TREBLE
BASS