Yamaha RXV1800 Owner's Manual - Page 130

Remote control, does not work or, function properly., SOURCE, does not learn new, functions.

Get Yamaha RXV1800 - AV Receiver PDF manuals and user guides
UPC - 027108928463
View all Yamaha RXV1800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 130 highlights

Troubleshooting ■ Remote control Problem The remote control does not work or function properly. The remote control does not learn new functions. Cause Remedy See page Wrong distance or angle. The remote control will function within a maximum 36 range of 6 m (20 ft) and no more than 30 degrees off- axis from the front panel. Direct sunlight or lighting (from an Reposition this unit. - inverter type of fluorescent lamp, etc.) is striking the remote control sensor of this unit. The batteries are weak. Replace all batteries. 5 The operation mode selector is set incorrectly. Set the operation mode selector correctly. When - operating this unit, set it to the CAMP position. When operating the component selected by the input selector button, set it to the CSOURCE position. When operating the TV set in the DTV or PHONO area, set it to the CTV position. The remote control code is not correctly Set the remote control code correctly using 102 set. "List of remote control codes" at the end of this manual. Try setting another code of the same manufacturer 102 using "List of remote control codes" at the end of this manual. The library code of the remote control and the remote control ID of this unit do not match. Match the remote control ID of this unit with the corresponding remote control library code. 103, 118 Even if the remote control code is Program the necessary functions independently into 104 correctly set, there are some models that the programmable buttons using the Learn feature. do not respond to the remote control. The batteries of this remote control and/or Replace the batteries. 5 the other remote control are too weak. The distance between the two remote Place the remote controls at the proper distance. 104 controls is too much or too little. The signal coding or modulation of the Learning is not possible. - other remote control is not compatible with this remote control. Memory capacity is full. Delete other unnecessary functions to make room for 109 the new functions. 126 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
126
En
Troubleshooting
■
Remote control
Problem
Cause
Remedy
See
page
The remote control
does not work or
function properly.
Wrong distance or angle.
The remote control will function within a maximum
range of 6 m (20 ft) and no more than 30 degrees off-
axis from the front panel.
36
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this unit.
—
The batteries are weak.
Replace all batteries.
5
The operation mode selector is set
incorrectly.
Set the operation mode selector correctly. When
operating this unit, set it to the
C
AMP
position.
When operating the component selected by the input
selector button, set it to the
C
SOURCE
position.
When operating the TV set in the DTV or PHONO
area, set it to the
C
TV
position.
—
The remote control code is not correctly
set.
Set the remote control code correctly using
“List of remote control codes” at the end of this
manual.
102
Try setting another code of the same manufacturer
using “List of remote control codes” at the end of this
manual.
102
The library code of the remote control and
the remote control ID of this unit do not
match.
Match the remote control ID of this unit with the
corresponding remote control library code.
103, 118
Even if the remote control code is
correctly set, there are some models that
do not respond to the remote control.
Program the necessary functions independently into
the programmable buttons using the Learn feature.
104
The remote control
does not learn new
functions.
The batteries of this remote control and/or
the other remote control are too weak.
Replace the batteries.
5
The distance between the two remote
controls is too much or too little.
Place the remote controls at the proper distance.
104
The signal coding or modulation of the
other remote control is not compatible
with this remote control.
Learning is not possible.
—
Memory capacity is full.
Delete other unnecessary functions to make room for
the new functions.
109