ZyXEL ARMOR Z1 - Model NBG6816 User Guide - Page 14

Wall Mounting, Be careful to avoid damaging pipes or cables located inside the wall

Page 14 highlights

Chapter 1 Introduction The following table describes the rear panel LEDs. Table 2 Rear Panel LEDs LED COLOR LAN 1-4 Green WAN Off Green Off STATUS On Blinking On Blinking DESCRIPTION The ARMOR Z1's LAN connection is ready. The ARMOR Z1 is sending/receiving data through the LAN. The LAN connection is not ready, or has failed. The ARMOR Z1's WAN connection is ready. The ARMOR Z1 is sending/receiving data through the WAN. The WAN connection is not ready, or has failed. 1.8 Wall Mounting You may need screw anchors if mounting on a concrete or brick wall. Table 3 Wall Mounting Information Distance between holes M4 Screws Screw anchors (optional) 12.45 cm Two Two 1 Select a position free of obstructions on a wall strong enough to hold the weight of the device. 2 Mark two holes on the wall at the appropriate distance apart for the screws. Be careful to avoid damaging pipes or cables located inside the wall when drilling holes for the screws. 3 If using screw anchors, drill two holes for the screw anchors into the wall. Push the anchors into the full depth of the holes, then insert the screws into the anchors. Do not insert the screws all the way in - leave a small gap of about 0.5 cm. If not using screw anchors, use a screwdriver to insert the screws into the wall. Do not insert the screws all the way in - leave a gap of about 0.5 cm. 4 Make sure the screws are fastened well enough to hold the weight of the ARMOR Z1 with the connection cables. 5 Align the holes on the back of the ARMOR Z1 with the screws on the wall. Hang the ARMOR Z1 on the screws. ARMOR Z1 User's Guide 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215

Chapter 1 Introduction
ARMOR Z1 User’s Guide
14
The following table describes the rear panel LEDs.
1.8
Wall Mounting
You may need screw anchors if mounting on a concrete or brick wall.
1
Select a position free of obstructions on a wall strong enough to hold the weight of the device.
2
Mark two holes on the wall at the appropriate distance apart for the screws.
Be careful to avoid damaging pipes or cables located inside the wall
when drilling holes for the screws.
3
If using screw anchors, drill two holes for the screw anchors into the wall. Push the anchors into the
full depth of the holes, then insert the screws into the anchors. Do not insert the screws all the way
in - leave a small gap of about 0.5 cm.
If not using screw anchors, use a screwdriver to insert the screws into the wall. Do not insert the
screws all the way in - leave a gap of about 0.5 cm.
4
Make sure the screws are fastened well enough to hold the weight of the ARMOR Z1 with the
connection cables.
5
Align the holes on the back of the ARMOR Z1 with the screws on the wall. Hang the ARMOR Z1 on
the screws.
Table 2
Rear Panel LEDs
LED
COLOR
STATUS
DESCRIPTION
LAN 1-4
Green
On
The ARMOR Z1’s LAN connection is ready.
Blinking
The ARMOR Z1 is sending/receiving data through the LAN.
Off
The LAN connection is not ready, or has failed.
WAN
Green
On
The ARMOR Z1’s WAN connection is ready.
Blinking
The ARMOR Z1 is sending/receiving data through the WAN.
Off
The WAN connection is not ready, or has failed.
Table 3
Wall Mounting Information
Distance between holes
12.45 cm
M4 Screws
Two
Screw anchors (optional)
Two