Home » ZyXEL Manuals » Networking » ZyXEL GS1500-24P » Manual Viewer

ZyXEL GS1500-24P User Guide - Page 56

System > Port Setting, continued

Get ZyXEL GS1500-24P PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Chapter 6 System Table 9 System > Port Setting (continued) LABEL DESCRIPTION Speed/ Duplex Select the speed and the duplex mode of the Ethernet connection on this port. Choices are Auto, 10M/Half, 10M/Full, 100M/Half, 100M/Full and 1000M/Full (Gigabit connections only). Selecting Auto (auto-negotiation) allows one port to negotiate with a peer port automatically to obtain the connection speed and duplex mode that both ends support. When auto-negotiation is turned on, a port on the Switch negotiates with the peer automatically to determine the connection speed and duplex mode. If the peer port does not support auto-negotiation or turns off this feature, the Switch determines the connection speed by detecting the signal on the cable and using half duplex mode. When the Switch's auto-negotiation is turned off, a port uses the pre-configured speed and duplex mode when making a connection, thus requiring you to make sure that the settings of the peer port are the same in order to connect. Flow Control A concentration of traffic on a port decreases port bandwidth and overflows buffer memory causing packet discards and frame losses. Flow Control is used to regulate transmission of signals to match the bandwidth of the receiving port. The Switch uses IEEE802.3x flow control in full duplex mode and backpressure flow control in half duplex mode. IEEE802.3x flow control is used in full duplex mode to send a pause signal to the sending port, causing it to temporarily stop sending signals when the receiving port memory buffers fill. Back Pressure flow control is typically used in half duplex mode to send a "collision" signal to the sending port (mimicking a state of packet collision) causing the sending port to temporarily stop sending signals and resend later. Select Flow Control to enable it. Apply Click Apply to save your changes to the Switch. Port The Port column displays the port number. State The State column indicates if the port is Enabled or Disabled. Speed/Duplex Config The Config column displays the port's Speed/Duplex configuration. Actual The Actual column displays the port's current Speed/Duplex status. Flow Control Config The Config column displays if Flow Control has been configured to be turned On or Off for the port. Actual The Actual column displays the port's current Flow Control status. 56 GS1500-24P User's Guide

Section	Page
GS1500-24P	1
About This User's Guide	3
Document Conventions	5
Safety Warnings	7
Contents Overview	9
Table of Contents	11
Introduction and Hardware	19
Getting to Know Your Switch	21
1.1 Introduction	21
1.1.1 Backbone Application	21
1.1.2 Bridging Example	22
1.1.3 High Performance Switching Example	23
1.1.4 IEEE 802.1Q VLAN Application Examples	23
1.2 Ways to Manage the Switch	24
1.3 Good Habits for Managing the Switch	24
Hardware Installation and Connection	27
2.1 Installation Scenarios	27
2.2 Desktop Installation Procedure	27
2.3 Mounting the Switch on a Rack	27
2.3.1 Rack-mounted Installation Requirements	28
2.3.2 Attaching the Mounting Brackets to the Switch	28
2.3.3 Mounting the Switch on a Rack	29
Hardware Panels	31
3.1 Overview	31
3.2 Front Panel	31
3.2.1 Gigabit Ethernet Ports	32
3.2.2 Mini-GBIC Slots	33
3.2.3 The RESET Button	35
3.3 Rear Panel	35
3.3.1 Power Connector	35
3.4 LEDs	35
Basic Configuration	37
The Web Configurator	39
4.1 Overview	39
4.2 System Login	39
4.3 The Status Screen	40
4.3.1 Change Your Password	44
4.4 Saving Your Configuration	44
4.5 Switch Lockout	44
4.6 Resetting the Switch	45
4.7 Logging Out of the Web Configurator	45
Initial Setup Example	47
5.1 Overview	47
5.1.1 Creating a VLAN	47
5.1.2 Setting Port VID	48
5.2 Configuring Switch Management IP Address	49
System	51
6.1 Overview	51
6.2 What You Can Do	51
6.3 Information	52
6.4 Time Setting	53
6.5 IP Setting Screen	53
6.6 User Account	54
6.7 Port Setting	55
Configuration	57
Link Aggregation	59
7.1 Overview	59
7.2 What You Can Do	59
7.3 What You Need to Know	59
7.3.1 Dynamic Link Aggregation	60
7.4 Trunk Group Setting	60
7.5 Trunk Distribution Algorithm	62
7.6 LACP Setting	63
7.7 Technical Reference	64
7.7.1 Static Trunking Example	64
VLAN	67
8.1 Overview	67
8.2 What You Can Do	67
8.3 What You Need to Know	67
8.3.1 IEEE 802.1Q Tagged VLANs	67
8.3.2 Forwarding Tagged and Untagged Frames	68
8.3.3 Common IEEE 802.1Q VLAN terminology	68
8.3.4 Static VLAN	69
8.4 Static VLAN	69
8.5 Port-based VLAN	71
Spanning Tree Protocol	73
9.1 Overview	73
9.2 What You Can Do	73
9.3 What You Need to Know	73
9.3.1 STP Terminology	74
9.3.2 How STP Works	74
9.3.3 STP Port States	74
9.4 STP Global Setting	75
9.5 STP Port Setting	77
QoS	79
10.1 Overview	79
10.2 What You Can Do	79
10.3 What You Need to Know	80
10.3.1 DiffServ	80
10.3.2 DSCP and Per-Hop Behavior	80
10.3.3 DiffServ Network Example	81
10.4 Port-based Priority	81
10.5 DSCP-to-IEEE 802.1p Priority Settings	82
10.5.1 DSCP-based Priority	83
10.6 Policy-based Priority	83
10.6.1 Policy-based Priority - Add/Modify	85
10.7 Priority to Queue Mapping	86
10.8 Packet Scheduling	87
10.8.1 Strictly Priority Queuing	87
10.8.2 Weighted Fair Queuing	87
10.8.3 Weighted Round Robin Scheduling (WRR)	88
Mirroring	91
11.1 Overview	91
11.2 What You Can Do	91
11.3 Port-based Mirroring	92
11.4 Policy-based Mirroring	93
11.4.1 Policy-based Mirroring - Add/Modify	93
SNMP	95
12.1 Overview	95
12.2 What You Can Do	95
12.3 What You Need to Know	95
12.3.1 About SNMP	95
12.4 SNMP Setting	97
12.5 SNMPv3 Setting	99
12.6 Technical Reference	103
Rate Limit	107
13.1 Rate Limit Overview	107
13.2 What You Can Do	107
13.3 Rate Limit Summary	107
13.3.1 Rate Limit Add/Modify	108
Bandwidth Control and Jumbo Frame	111
14.1 Bandwidth Control and Jumbo Frame Overview	111
14.2 What You Can Do	111
14.3 Bandwidth Control	112
14.4 Jumbo Frame Setting	113
Power Over Ethernet	115
15.1 Power Over Ethernet Overview	115
15.2 What You Can Do	115
15.3 Power Over Ethernet	116
Security	119
MAC Address	121
16.1 Overview	121
16.2 What You Can Do	121
16.2.1 MAC Forwarding Table	122
16.2.2 Static MAC Address Forwarding	122
16.3 MAC Forwarding Table	123
16.4 Static MAC	123
16.5 MAC Filtering	124
802.1x	127
17.1 Overview	127
17.2 What You Can Do	127
17.3 What You Need to Know	128
17.3.1 IEEE 802.1x Authentication	128
17.4 Port Authentication Configuration	128
17.5 802.1x Setting	129
17.6 802.1x Port Setting	130
Dynamic ARP	131
18.1 ARP Table Overview	131
18.2 What You Can Do	131
18.3 What You Need to Know	131
18.3.1 ARP Table Entries	132
18.3.2 How Dynamic ARP Works	132
18.3.3 ARP Inspection Overview	132
18.3.4 MAC-IP Binding	133
18.4 Dynamic ARP Setting	133
18.5 Dynamic ARP VLAN Setting	134
18.6 MAC-IP Binding Config	135
Storm Control	137
19.1 Overview	137
19.2 What You Can Do	137
19.3 Storm Control Setting	138
Defence Engine	139
20.1 Overview	139
20.2 What You Can Do	139
20.3 Activating Defence Engine	139
Monitoring and Tools	141
Monitoring	143
21.1 Overview	143
21.2 What You Can Do	143
21.3 Logging Setting	143
21.4 Logging Viewing	145
21.5 Port Statistics	147
Tools	149
22.1 Overview	149
22.2 What You Can Do	149
22.3 TFTP	149
22.4 Reset	151
22.5 Reboot	151
Troubleshooting & Product Specifications	155
Troubleshooting	157
23.1 Power, Hardware Connections, and LEDs	157
23.2 Switch Access and Login	158
Product Specifications	161
Appendices and Index	167
Changing a Fuse	169
Common Services	171
Legal Information	175
Open Software Announcements	179

Match case Limit results 1 per page

Chapter 6 System

GS1500-24P User’s Guide

Speed/

Duplex

Select the speed and the duplex mode of the Ethernet connection on this

port. Choices are

Auto

10M/Half

10M/Full

100M/Half

100M/Full

and

1000M/Full

(Gigabit connections only).

Selecting

Auto

(auto-negotiation) allows one port to negotiate with a peer

port automatically to obtain the connection speed and duplex mode that

both ends support. When auto-negotiation is turned on, a port on the

Switch negotiates with the peer automatically to determine the connection

speed and duplex mode. If the peer port does not support auto-negotiation

or turns off this feature, the Switch determines the connection speed by

detecting the signal on the cable and using half duplex mode. When the

Switch’s auto-negotiation is turned off, a port uses the pre-configured

speed and duplex mode when making a connection, thus requiring you to

make sure that the settings of the peer port are the same in order to

connect.

Flow Control

A concentration of traffic on a port decreases port bandwidth and overflows

buffer memory causing packet discards and frame losses.

Flow Control

used to regulate transmission of signals to match the bandwidth of the

receiving port.

The Switch uses IEEE802.3x flow control in full duplex mode and

backpressure flow control in half duplex mode.

IEEE802.3x flow control is used in full duplex mode to send a pause signal

to the sending port, causing it to temporarily stop sending signals when

the receiving port memory buffers fill.

Back Pressure flow control is typically used in half duplex mode to send a

"collision" signal to the sending port (mimicking a state of packet collision)

causing the sending port to temporarily stop sending signals and resend

later. Select

Flow Control

to enable it.

Apply

Click

Apply

to save your changes to the Switch.

Port

The

Port

column displays the port number.

State

The

State

column indicates if the port is

Enabled

Disabled

Speed/Duplex

Config

The

Config

column displays the port’s

Speed/Duplex

configuration.

Actual

The

Actual

column displays the port’s current

Speed/Duplex

status.

Flow Control

Config

The

Config

column displays if

Flow Control

has been configured to be

turned

Off

for the port.

Actual

The

Actual

column displays the port’s current

Flow Control

status.

Table 9

System > Port Setting

(continued)

LABEL

DESCRIPTION