Home » ZyXEL Manuals » Networking » ZyXEL GS1500-24P » Manual Viewer

ZyXEL GS1500-24P User Guide - Page 7

Safety Warnings - 24

Get ZyXEL GS1500-24P PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Safety Warnings Safety Warnings • Do NOT use this product near water, for example, in a wet basement or near a swimming pool. • Do NOT expose your device to dampness, dust or corrosive liquids. • Do NOT store things on the device. • Do NOT install, use, or service this device during a thunderstorm. There is a remote risk of electric shock from lightning. • Do not obstruct the device ventillation slots as insufficient airflow may harm your device. • Connect ONLY suitable accessories to the device. • Do NOT open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other risks. ONLY qualified service personnel should service or disassemble this device. Please contact your vendor for further information. • Make sure to connect the cables to the correct ports. • Place connecting cables carefully so that no one will step on them or stumble over them. • Always disconnect all cables from this device before servicing or disassembling. • Use ONLY an appropriate power adaptor or cord for your device. Connect it to the right supply voltage (for example, 110V AC in North America or 230V AC in Europe). • Use ONLY power wires of the appropriate wire gauge (see Chapter 24 on page 161 for details) for your device. Connect it to a power supply of the correct voltage (see Chapter 24 on page 161 for details). • Do NOT allow anything to rest on the power adaptor or cord and do NOT place the product where anyone can walk on the power adaptor or cord. • Do NOT use the device if the power adaptor or cord is damaged as it might cause electrocution. • If the power adaptor or cord is damaged, remove it from the device and the power source. • Do NOT attempt to repair the power adaptor or cord. Contact your local vendor to order a new one. • Fuse Warning! Replace a fuse only with a fuse of the same type and rating. • The length of exposed (bare) power wire should not exceed 7 mm. • For pluggable equipment (equipment that doesn't have a fixed power connection), the socket-outlet shall be installed near the equipment and shall be easily accessible (install the device within reach of a power outlet and keep the area free of obstructions). Your product is marked with this symbol, which is known as the WEEE mark. WEEE stands for Waste Electronics and Electrical Equipment. It means that used electrical and electronic products should not be mixed with general waste. Used electrical and electronic equipment should be treated separately. GS1500-24P User's Guide 7

Section	Page
GS1500-24P	1
About This User's Guide	3
Document Conventions	5
Safety Warnings	7
Contents Overview	9
Table of Contents	11
Introduction and Hardware	19
Getting to Know Your Switch	21
1.1 Introduction	21
1.1.1 Backbone Application	21
1.1.2 Bridging Example	22
1.1.3 High Performance Switching Example	23
1.1.4 IEEE 802.1Q VLAN Application Examples	23
1.2 Ways to Manage the Switch	24
1.3 Good Habits for Managing the Switch	24
Hardware Installation and Connection	27
2.1 Installation Scenarios	27
2.2 Desktop Installation Procedure	27
2.3 Mounting the Switch on a Rack	27
2.3.1 Rack-mounted Installation Requirements	28
2.3.2 Attaching the Mounting Brackets to the Switch	28
2.3.3 Mounting the Switch on a Rack	29
Hardware Panels	31
3.1 Overview	31
3.2 Front Panel	31
3.2.1 Gigabit Ethernet Ports	32
3.2.2 Mini-GBIC Slots	33
3.2.3 The RESET Button	35
3.3 Rear Panel	35
3.3.1 Power Connector	35
3.4 LEDs	35
Basic Configuration	37
The Web Configurator	39
4.1 Overview	39
4.2 System Login	39
4.3 The Status Screen	40
4.3.1 Change Your Password	44
4.4 Saving Your Configuration	44
4.5 Switch Lockout	44
4.6 Resetting the Switch	45
4.7 Logging Out of the Web Configurator	45
Initial Setup Example	47
5.1 Overview	47
5.1.1 Creating a VLAN	47
5.1.2 Setting Port VID	48
5.2 Configuring Switch Management IP Address	49
System	51
6.1 Overview	51
6.2 What You Can Do	51
6.3 Information	52
6.4 Time Setting	53
6.5 IP Setting Screen	53
6.6 User Account	54
6.7 Port Setting	55
Configuration	57
Link Aggregation	59
7.1 Overview	59
7.2 What You Can Do	59
7.3 What You Need to Know	59
7.3.1 Dynamic Link Aggregation	60
7.4 Trunk Group Setting	60
7.5 Trunk Distribution Algorithm	62
7.6 LACP Setting	63
7.7 Technical Reference	64
7.7.1 Static Trunking Example	64
VLAN	67
8.1 Overview	67
8.2 What You Can Do	67
8.3 What You Need to Know	67
8.3.1 IEEE 802.1Q Tagged VLANs	67
8.3.2 Forwarding Tagged and Untagged Frames	68
8.3.3 Common IEEE 802.1Q VLAN terminology	68
8.3.4 Static VLAN	69
8.4 Static VLAN	69
8.5 Port-based VLAN	71
Spanning Tree Protocol	73
9.1 Overview	73
9.2 What You Can Do	73
9.3 What You Need to Know	73
9.3.1 STP Terminology	74
9.3.2 How STP Works	74
9.3.3 STP Port States	74
9.4 STP Global Setting	75
9.5 STP Port Setting	77
QoS	79
10.1 Overview	79
10.2 What You Can Do	79
10.3 What You Need to Know	80
10.3.1 DiffServ	80
10.3.2 DSCP and Per-Hop Behavior	80
10.3.3 DiffServ Network Example	81
10.4 Port-based Priority	81
10.5 DSCP-to-IEEE 802.1p Priority Settings	82
10.5.1 DSCP-based Priority	83
10.6 Policy-based Priority	83
10.6.1 Policy-based Priority - Add/Modify	85
10.7 Priority to Queue Mapping	86
10.8 Packet Scheduling	87
10.8.1 Strictly Priority Queuing	87
10.8.2 Weighted Fair Queuing	87
10.8.3 Weighted Round Robin Scheduling (WRR)	88
Mirroring	91
11.1 Overview	91
11.2 What You Can Do	91
11.3 Port-based Mirroring	92
11.4 Policy-based Mirroring	93
11.4.1 Policy-based Mirroring - Add/Modify	93
SNMP	95
12.1 Overview	95
12.2 What You Can Do	95
12.3 What You Need to Know	95
12.3.1 About SNMP	95
12.4 SNMP Setting	97
12.5 SNMPv3 Setting	99
12.6 Technical Reference	103
Rate Limit	107
13.1 Rate Limit Overview	107
13.2 What You Can Do	107
13.3 Rate Limit Summary	107
13.3.1 Rate Limit Add/Modify	108
Bandwidth Control and Jumbo Frame	111
14.1 Bandwidth Control and Jumbo Frame Overview	111
14.2 What You Can Do	111
14.3 Bandwidth Control	112
14.4 Jumbo Frame Setting	113
Power Over Ethernet	115
15.1 Power Over Ethernet Overview	115
15.2 What You Can Do	115
15.3 Power Over Ethernet	116
Security	119
MAC Address	121
16.1 Overview	121
16.2 What You Can Do	121
16.2.1 MAC Forwarding Table	122
16.2.2 Static MAC Address Forwarding	122
16.3 MAC Forwarding Table	123
16.4 Static MAC	123
16.5 MAC Filtering	124
802.1x	127
17.1 Overview	127
17.2 What You Can Do	127
17.3 What You Need to Know	128
17.3.1 IEEE 802.1x Authentication	128
17.4 Port Authentication Configuration	128
17.5 802.1x Setting	129
17.6 802.1x Port Setting	130
Dynamic ARP	131
18.1 ARP Table Overview	131
18.2 What You Can Do	131
18.3 What You Need to Know	131
18.3.1 ARP Table Entries	132
18.3.2 How Dynamic ARP Works	132
18.3.3 ARP Inspection Overview	132
18.3.4 MAC-IP Binding	133
18.4 Dynamic ARP Setting	133
18.5 Dynamic ARP VLAN Setting	134
18.6 MAC-IP Binding Config	135
Storm Control	137
19.1 Overview	137
19.2 What You Can Do	137
19.3 Storm Control Setting	138
Defence Engine	139
20.1 Overview	139
20.2 What You Can Do	139
20.3 Activating Defence Engine	139
Monitoring and Tools	141
Monitoring	143
21.1 Overview	143
21.2 What You Can Do	143
21.3 Logging Setting	143
21.4 Logging Viewing	145
21.5 Port Statistics	147
Tools	149
22.1 Overview	149
22.2 What You Can Do	149
22.3 TFTP	149
22.4 Reset	151
22.5 Reboot	151
Troubleshooting & Product Specifications	155
Troubleshooting	157
23.1 Power, Hardware Connections, and LEDs	157
23.2 Switch Access and Login	158
Product Specifications	161
Appendices and Index	167
Changing a Fuse	169
Common Services	171
Legal Information	175
Open Software Announcements	179

Match case Limit results 1 per page

Safety Warnings

GS1500-24P User’s Guide

Safety Warnings

•

Do NOT use this product near water, for example, in a wet basement or near a swimming

pool.

•

Do NOT expose your device to dampness, dust or corrosive liquids.

•

Do NOT store things on the device.

•

Do NOT install, use, or service this device during a thunderstorm. There is a remote risk

of electric shock from lightning.

•

Do not obstruct the device ventillation slots as insufficient airflow may harm your device.

•

Connect ONLY suitable accessories to the device.

•

Do NOT open the device or unit. Opening or removing covers can expose you to

dangerous high voltage points or other risks. ONLY qualified service personnel should

service or disassemble this device. Please contact your vendor for further information.

•

Make sure to connect the cables to the correct ports.

•

Place connecting cables carefully so that no one will step on them or stumble over them.

•

Always disconnect all cables from this device before servicing or disassembling.

•

Use ONLY an appropriate power adaptor or cord for your device. Connect it to the right

supply voltage (for example, 110V AC in North America or 230V AC in Europe).

•

Use ONLY power wires of the appropriate wire gauge (see

Chapter 24 on page 161

for

details) for your device. Connect it to a power supply of the correct voltage (see

Chapter

24 on page 161

for details).

•

Do NOT allow anything to rest on the power adaptor or cord and do NOT place the

product where anyone can walk on the power adaptor or cord.

•

Do NOT use the device if the power adaptor or cord is damaged as it might cause

electrocution.

•

If the power adaptor or cord is damaged, remove it from the device and the power

source.

•

Do NOT attempt to repair the power adaptor or cord. Contact your local vendor to order a

new one.

•

Fuse Warning! Replace a fuse only with a fuse of the same type and rating.

•

The length of exposed (bare) power wire should not exceed 7 mm.

•

For pluggable equipment (equipment that doesn’t have a fixed power connection), the

socket-outlet shall be installed near the equipment and shall be easily accessible (install

the device within reach of a power outlet and keep the area free of obstructions).

Your product is marked with this symbol, which is known as the WEEE mark.

WEEE stands for Waste Electronics and Electrical Equipment. It means that used

electrical and electronic products should not be mixed with general waste. Used

electrical and electronic equipment should be treated separately.