ZyXEL WAP3205 v2 User Guide - Page 46

Setting your WAP3205 to AP Mode, 6.3.2 Accessing the Web Configurator in Access Point Mode - instructions

Page 46 highlights

Chapter 6 Access Point Mode 6.3.1 Setting your WAP3205 to AP Mode 1 Log into the Web Configurator if you haven't already. See the Quick start Guide for instructions on how to do this. 2 To use your WAP3205 as an access point, go to Maintenance > Sys OP Mode and select Access Point mode. Figure 21 Changing to Access Point mode Note: You have to log in to the Web Configurator again when you change modes. As soon as you do, your WAP3205 is already in Access Point mode. 6.3.2 Accessing the Web Configurator in Access Point Mode Log in to the Web Configurator in Access Point mode, do the following: 1 Connect your computer to the LAN port of the WAP3205. 2 The default IP address of the WAP3205 is "192.168.1.2". In this case, your computer must have an IP address in the range between "192.168.1.3" and "192.168.1.254". 3 Click Start > Run on your computer in Windows. Type "cmd" in the dialog box. Enter "ipconfig" to show your computer's IP address. If your computer's IP address is not in the correct range then see Appendix C on page 149 for information on changing your computer's IP address. 4 After you've set your computer's IP address, open a web browser such as Internet Explorer and type "192.168.1.2" as the web address in your web browser. Note: After clicking Login, the Easy mode appears. Refer to Section on page 35 for the Easy mode screens. Change to Expert mode to see the screens described in the sections following this. 46 WAP3205 User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196

Chapter 6 Access Point Mode
WAP3205 User’s Guide
46
6.3.1
Setting your WAP3205 to AP Mode
1
Log into the Web Configurator if you haven’t already. See the Quick start Guide for
instructions on how to do this.
2
To use your WAP3205 as an access point, go to
Maintenance > Sys OP Mode
and select
Access Point mode.
Figure 21
Changing to Access Point mode
Note: You have to log in to the Web Configurator again when you change modes. As
soon as you do, your WAP3205 is already in Access Point mode.
6.3.2
Accessing the Web Configurator in Access Point Mode
Log in to the Web Configurator in Access Point mode, do the following:
1
Connect your computer to the LAN port of the WAP3205.
2
The default IP address of the WAP3205 is “192.168.1.2”. In this case, your
computer must have an IP address in the range between “192.168.1.3” and
“192.168.1.254”.
3
Click
Start > Run
on your computer in Windows. Type “cmd” in the dialog box.
Enter “ipconfig” to show your computer’s IP address. If your computer’s IP
address is not in the correct range then see
Appendix C on page 149
for
information on changing your computer’s IP address.
4
After you’ve set your computer’s IP address, open a web browser such as Internet
Explorer and type “192.168.1.2” as the web address in your web browser.
Note: After clicking
Login
, the Easy mode appears. Refer to
Section
on page 35
for
the Easy mode screens. Change to Expert mode to see the screens described
in the sections following this.