HP StorageWorks 2/32 SAN switch 2/32 version 4.0.x installation guide
HP StorageWorks 2/32 - SAN Switch Manual
View all HP StorageWorks 2/32 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP StorageWorks 2/32 manual content summary:
- HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 1
installation guide hp StorageWorks SAN switch 2/32 Product Version: 4.0.x Second Edition (February 2003) Part Number: AA-RTQVB-TE This installation guide provides basic procedures for setting up, configuring, and managing the SAN Switch 2/32 and SAN Switch 2/32 Power Pak models. - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 2
UNIX® is a registered trademark of The Open Group. BROCADE, the Brocade B weave logo, Brocade: the Intelligent Platform for Networking Storage, SilkWorm, and an additional warranty. Printed in the U.S.A. SAN Switch 2/32 Installation Guide Second Edition (February 2003) Part Number: AA-RTQVB-TE - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 3
14 Getting Help 15 HP Technical Support 15 HP Storage Website 15 HP Authorized Reseller 15 1 Overview 17 SAN Switch 2/32 Features 18 Firmware 18 Hardware 18 Port Side of the SAN Switch 2/32 19 Optical Ports 20 Fan Assembly Side of the SAN Switch 2/32 20 Optional Hardware Kits 21 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 4
in the Optional HP System/e Rack 40 Connecting AC Power 45 Power On Self-Test 46 Checking POST Results 46 Configuring SAN Switch 2/32 Network Addressing 47 Requirements 47 Setting Network Addresses via a Serial Connection 47 Connecting the SAN Switch 2/32 to the LAN 51 Core Switch PID Format - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 5
for Switches Running Firmware Lower than V4.0.0 93 Updating the Core Switch PID Format Online 93 Updating the Core Switch PID Format Offline 95 HP/UX Procedure for Updating the Core Switch PID Format 97 AIX Procedure for Updating the Core Switch PID Format 99 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 6
the Ethernet cable 51 15 Inserting a cable into an SFP 57 16 LEDs on port side of SAN Switch 2/32 62 17 LEDs on non-port side of SAN Switch 2/32 65 18 Power supplies and fan assemblies locations 75 19 Power supplies and fan assemblies locations 76 6 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 7
Operation 63 5 Non-Port Side LED Patterns During Normal Operation 66 6 Management Options for the SAN Switch 2/32 68 7 Physical Specifications 86 8 Power Supply Specifications 87 9 Environmental Requirements 88 10 Cabling Pinouts if Pin 7 is Used 90 SAN Switch 2/32 Installation Guide 7 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 8
Contents 8 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 9
This installation guAidbe porouvitdetshinisforGmautioindtoehelp you: ■ Set up and configure thAebohupt thSistoGruaidgeeWorks SAN Switch 2/32. ■ Maintain and operate the switch. About this Guide topics include: ■ Overview, page 10 ■ Conventions, page 11 ■ Rack Stability, page 14 ■ Getting Help, page - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 10
and firmware releases, please visit the following HP StorageWorks website: http://www.q.c.com/storage/productindexdisk.html For information about Fibre Channel standards, visit the Fibre Channel Association website, located at http://www.fibrechannel.com. 10 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 11
User input hp.com Text Symbols The following symbols may be found in the text of this guide. They have the following meanings. WARNING: Text set off in this manner indicates that failure to follow directions in the warning could result in bodily harm or death. SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 12
these symbols indicates the presence of electrical shock hazards. Enclosed area contains no operator serviceable parts. WARNING: To reduce the risk to personal safety from electrical shock hazards, hot component, allow the surface to cool before touching. 12 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 13
handle safely. WARNING: To reduce the risk to personal safety or damage to the equipment, observe local occupational health and safety requirements and guidelines for manually handling material. SAN Switch 2/32 Installation Guide 13 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 14
About this Guide Rack Stability Rack stability protects personnel and equipment. WARNING: To reduce the risk of personal safety or damage to the extended at any time. A rack may become unstable if more than one rack component is extended for any reason. 14 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 15
.hp.com/country/us/eng/prodserv/storage.html. From this website, select the appropriate product or solution. HP Authorized Reseller For the name of your nearest HP authorized reseller: ■ In the United States, call 1-800-345-1518 ■ In Canada, call 1-800-263-5868 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 16
About this Guide ■ Elsewhere, see the HP website for locations and telephone numbers: http://www.hp.com. 16 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 17
Overview 1 The HP StorageWorks SAN Switch 2/32 is a high-performance, 32-port, 2 gigabit (Gb) Fibre Channel switch used to interconnect storage devices, hosts, and servers in a Storage Area Network (SAN). It integrates Fabric Operating System (FOS) firmware V4.0.2x or higher, and is compatible - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 18
Electronic Industries Association (EIA) 19-inch rack ■ 32 Fibre Channel ports ■ One RS-232 Serial port, designed to connect to a DTE port ■ One 10/100 Mb/s Ethernet port with an RJ-45 connector ■ Two redundant power supplies, with AC switches and built-in fans 18 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 19
on each fan assembly Port Side of the SAN Switch 2/32 Figure 1 shows the port side of the SAN Switch 2/32. 1 2 3 5 1 Serial port 4 Power switch 2 Fibre Channel 5 Ethernet port port 3 IP address label Figure 1: Port side of the SAN Switch 2/32 4 SHR-2568A SAN Switch 2/32 Installation Guide 19 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 20
HP StorageWorks ISL Trunking Version 3.0.x/4.0.x User Guide. Fan Assembly Side of the SAN Switch 2/32 Figure 2 shows the fan assembly side of the SAN Switch 2/32. The fan assembly side houses the fans with corresponding LEDs, power supplies, and the port readiness LED. 1 2 3 4 1 Power supply - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 21
Hardware Kits HP provides the following optional hardware kits in support of the SAN Switch 2/32; see Table 2. Table 2: SAN Switch 2/32 Orderable Hardware Accessory ** 221691-B27** C7534A* C7534A* * premerger HP part number ** premerger Compaq part number SAN Switch 2/32 Installation Guide 21 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 22
Overview 22 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 23
EIA Cabinet, page 31 ■ Installing the Switch in the Optional HP System/e Rack, page 40 ■ Connecting AC Power. page 45 ■ Power On Self-Test, page 46 ■ Configuring SAN Switch 2/32 Network Addressing, page 47 ■ Connecting the SAN Switch 2/32 to the LAN, page 51 ■ Core Switch PID Format Summary, page 52 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 24
Kit shown in Figure 3 may not represent the kit that shipped with your switch. HP reserves the right to substitute Rack Mount Kits, providing applicable instructions with each switch. 3. Verify that the carton contains the items shown in Figure 3 and Table 3. 24 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 25
Installing the SAN Switch 2/32 Note: If any items are damaged or missing, please contact HP or an HP authorized reseller. 1 2 3 Figure 3: Shipping carton contents SAN Switch 2/32 Installation Guide SHR-2570A 25 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 26
2 3 Item One HP StorageWorks SAN Switch 2/32 product accessories box containing: ■ One RS-232 Serial cable (convertible to an RJ-45 connector, by removing the adapter on the end of the cable) ■ Rack Mount hardware pouch: - Power cord clips (6) - 3-hole bar nuts (4) - 10-32 x 3/8 inch Black Phillips - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 27
2/32 Locating SAN Switch 2/32 Serial Numbers Before contacting HP for technical support or service, obtain the three serial numbers located on the switch. Each serial number provides specific logistical information, identifying the device's manufacturing location. SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 28
for all components in the rack is flowing in the same front-to-back direction. Note: HP highly recommends mounting the switch in a cabinet or rack so that the fans reside in the front of the cabinet, and the ports (cables) reside in the rear of the cabinet. 28 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 29
of 47-63 Hz ■ Power capability of 75 W maximum The switch has a universal power supply capable of functioning worldwide without voltage jumpers or switches. The power supply is auto ranging in terms of accommodating input voltages and line frequencies. SAN Switch 2/32 Installation Guide 29 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 30
automatically runs a Power On Self-Test (POST). Caution: Do not connect the switch to the network until the IP address is correctly set. For instructions on how to set the IP address, see "Configuring SAN Switch 2/32 Network Addressing," later in this chapter. 30 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 31
Switch 2/32 Installing the SAN Switch 2/32 in an HP Series 9000 or EIA Cabinet Read the following sections for complete installation instructions. Before you begin, obtain the following tools: ■ #2 Phillips screwdriver, with torque capability ■ Torx screwdriver ■ Slotted blade screwdriver, 1/4 inch - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 32
using the Phillips head, 8-32 x 3/16 inch screws supplied in the Rack Mount Kit. Installing screws longer than 3/16 inch can damage the switch. 1. Position the inner slide rails with the flat side against the switch, oriented in one of the following two ways: 32 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 33
supply end of the switch. b. To allow the power supply side of the switch to slide out the front of the rack: Orient the inner slide rail with the end containing the lock release lever towards the port end of the switch. 2. Locate three Phillips head, 8-32 x 3/16 inch screws provided in the Rack - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 34
the two screw holes at the port end of the switch. 2. Locate two Phillips head 8-32 x 3/16 inch screws, contained in the Rack Mount Kit. Secure the right mount bracket to the switch; see Figure 5. Figure 5: Attaching the rear rack mount brackets SHR-2576A 34 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 35
the outer slide rails in the HP 9000 Series Rack. Obtain the following items, located in the Rack Mount Kit: ■ Four 3-hole bar nuts ■ Eight Phillips head 8-32 x 3/8 inch screws ■ Eight square alignment washers ■ # 2 Phillips screwdriver with torque capability SAN Switch 2/32 Installation Guide 35 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 36
's rail and the L-bracket at the end of the outer slide rail, Figure 6. Note: Position the square alignment washers onto the Phillips head 10-32 x 3/8 inch screws, as described in step 3. The square alignment washers are mandatory for proper switch alignment. 36 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 37
Outer slide rail SHR-2478A 4 L-Brackets 5 Power cord clip (1 of 6) Figure 6: Attaching the outer slide rails to the HP 9000 Series rack Note: Remember to position the 3-hole bar nut behind the L-bracket. 8. Tighten the screws, and torque to 25 inch-pounds. SAN Switch 2/32 Installation Guide 37 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 38
Rack Mounting Procedure Read this section to finalize the rack mount procedure. Positioning the Switch in the HP 9000 Series Rack Follow these steps to install the switch in the rack. Note: If installing more than one SAN Switch 2/32 directly on top of one another (in a 3U space), you must mount the - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 39
or Front Rack Mount Brackets") to the rack rails, as follows: 1. Locate two Phillips head 10-32 x 3/8 inch screws in the Rack Mount Kit accessory pouch. 2. Secure each rack mount bracket to the rack rails. 3. Tighten the screws, and torque to 25 inch-pounds. SAN Switch 2/32 Installation Guide 39 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 40
Installing the SAN Switch 2/32 Installing the Switch in the Optional HP System/e Rack This section provides instructions for installing the SAN Switch 2/32 in the optional HP System/e rack. The HP System/e Rack Kit consists of the following items: ■ HP System/e Rack Rail Kit - pre-merger HP part - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 41
Installing the SAN Switch 2/32 2. Choose a mounting location in the rack for the switch. 3. Install each of the two mounting brackets with (1) M5 Torx head screw with captive lock top and bottom positions of the three-hole EIA pattern as shown in Figure 9. SAN Switch 2/32 Installation Guide 41 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 42
Installing the SAN Switch 2/32 SHR-2582A Figure 9: Installing the Tinnerman clips 5. Assemble the outer rails by completing the following steps: a. As an b. Insert the alignment pins attached to the outer rail front flange into the center opening in the rack. 42 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 43
illustration as required. [8] Adjust the size of the outer graphic frame as required. Delete this set of instructions 1 2 1 Rubber washer (1 of 2) 2 Rear rail tray bracket (1 of 2) Figure 10: the upper left and the lower right screws until step 9. SAN Switch 2/32 Installation Guide 43 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 44
" for steps on applying power to the switch. Caution: Do not connect the switch to the network until the IP address is correctly set. For instructions on how to set the IP address, see "Configuring SAN Switch 2/32 Network Addressing," later in this chapter. 44 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 45
power off). The switch automatically runs POST. WARNING: Do not connect the switch to the network until the IP address is correctly set. For instructions on setting the IP address, see "Configuring SAN Switch 2/32 Network Addressing," later in this chapter. SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 46
SAN Switch 2/32 Power On Self-Test Each time the switch is powered on, rebooted, or reset, the switch automatically runs POST. During POST, the port status LEDs flash, verifying that the switch the HP StorageWorks Fabric OS Version 3.0.x/4.0.x Reference Guide. 46 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 47
for information on how to configure the SAN Switch 2/32 addressing scheme. For instructions about configuring the switch to operate in a fabric containing switches from other vendors, refer to the HP StorageWorks Fabric OS Procedures Version 3.0.x/4.0.x User Guide. For detailed information about the - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 48
5. Power on the workstation and establish a connection to the switch using a terminal emulator application (such as Hyperterminal). Note: These steps show instructions specific to Hyperterminal. If using a different application, consult the specific application's documentation. 48 SAN Switch 2/32 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 49
being changed... Committing configuration...Done. switch:admin> c. To verify that the IP address was entered correctly, type: ipAddrShow d. Once the IP address is verified as correct, remove the Serial cable, and replace the shipping plug in the Serial port. SAN Switch 2/32 Installation Guide 49 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 50
only for use during the initial setting of the IP address and for service purposes. Using the Serial port during normal switch operation or for regular maintenance is not recommended. 8. Record the IP address on the label affixed to the SAN Switch 2/32. 50 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 51
Tools application. Verify that the switch is not accessed from any other connections during the remaining steps. 4. Login to the switch with administrative privileges by telnet. The default administrative logon is admin and the default password is password. SAN Switch 2/32 Installation Guide 51 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 52
Switch 2/32 and HP StorageWorks Core Switch 2/64 always use Core Switch PID format 1. This parameter is always 1 and cannot be changed. Important Information on Checking the Core Switch PID Format Updating the Core Switch PID Format is necessary when upgrading an existing SAN to support larger port - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 53
Installing the SAN Switch 2/32 For detailed recommendations and instructions on updating the Core Switch PID, please refer to Appendix B in this guide, "Updating the Core Switch PID Format." SAN Switch 2/32 Installation Guide 53 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 54
the SAN Switch 2/32 Optional Configuration Settings The following sections describe how to modify domain IDs and status policies. Modifying Domain IDs Optional. Modify the domain IDs, if desired, as follows. Note: The default domain ID is 1. If the default domain ID is already in use when the switch - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 55
Installing the SAN Switch 2/32 Note: Configure each port to match the topology of each host or target before connecting to the device. The default port configuration is fabric, not private loop. The switch does not auto-sense topology. SAN Switch 2/32 Installation Guide 55 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 56
to connect the SFPs and cables to SAN Switch 2/32 ports as required. Note: The ports and cables used in trunking groups must meet specific requirements. For a list of these requirements, refer to the HP StorageWorks ISL Trunking Version 3.0.x/4.0.x User Guide. 1. Remove the shipping plug from the - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 57
For instructions on how to back up the configuration, refer to Chapter 4, "Backing Up Configuration Data and Upgrading Firmware." Or, for more detailed information and commands, refer to the HP StorageWorks Fabric OS Procedures Version 3.0.x/4.0.x User Guide. SAN Switch 2/32 Installation Guide 57 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 58
. The default domain setting is 1. Note: If a switch boot failure occurs, the switch must be taken offline for repair or replacement. Contact your HP Technical Support for assistance. 5. Power off the new switch and connect one Fibre Channel cable from the SAN to the new switch. 58 SAN Switch 2/32 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 59
to remove and replace the switch). ■ If using ISL Trunking: - Group cables by trunking groups. - The cables used in trunking groups must meet specific requirements. For a list of these requirements, refer to the HP StorageWorks ISL Trunking Version 3.0.x/4.0.x User Guide. ■ Label the fiber optic - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 60
Installing the SAN Switch 2/32 60 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 61
the SAN Switch 2/32 3 This chapter covers the following topics: ■ Interpreting LED Activity, page 62 ■ Management Overview, page 68 ■ Running Basic Switch Operations Using Telnet, page 70 ■ SAN Switch 2/32 Diagnostics, page 74 ■ Field Replaceable Units, page 75 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 62
the error log, refer to the HP StorageWorks Fabric OS Procedures Version 3.0.x/4.0.x User Guide. LEDs on the Port Side of the Switch The port side of the switch contains the following LEDs; see Figure 16: ■ One Switch Power/Status LED on right side ■ One Port Status LED next to each Fibre Channel - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 63
. Port is online (connected to external device) but has no traffic. Port is online but segmented, indicating a loopback cable or incompatible switch. No action required. Verify correct device is connected to port, and switch and port settings are correct. SAN Switch 2/32 Installation Guide 63 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 64
Status Port is in internal loopback (diagnostic). Port is online, with traffic flowing through port. POST is running. Port is switch from a management station. 1. Check transceiver and cable or loopback plugs for correct insertion. 2. Check and clear error log. 64 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 65
Failure LED at the top of each fan assembly (inside the bezel) 1 2 3 SHR-2579A 1 Power supply LED 2 Fan failure LED 3 Port readiness LED Figure 17: LEDs on non-port side of SAN Switch 2/32 Table 5 describes the LEDs on the non-port side of the switch. SAN Switch 2/32 Installation Guide 65 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 66
, error log, Port Status LEDs, transceivers, cables, and loopback plugs. 2. Correct error condition. 3. Clear error log. 4. Rerun diagnostics to verify fix. Verify power supply is on and seated, and power cord is connected to a functioning power source. 66 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 67
either healthy or is not receiving power. Flashing orange (on 1 second; off 1 second) Fan assembly has failed. Recommended Action No action required. Verify power supply is on and power cord is connected to a functioning power source. Replace fan assembly. SAN Switch 2/32 Installation Guide 67 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 68
Note: For information about upgrading the version of Fabric OS installed on the switch, refer to the HP StorageWorks Fabric OS Procedures Version 3.0.x/4.0.x User Guide. Table 6: Management Options for the SAN Switch 2/32 Management Tool Command Line Interface (CLI) Runs up to two admin sessions - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 69
Options for the SAN Switch 2/32 (Continued) Management Tool Management server For more information, refer to the HP StorageWorks Fabric OS Procedures Version 3.0.x/4.0.x User Guide and the HP StorageWorks Fabric OS Version 3.0.x/4.0.x Reference Guide. Out-of-band Support Ethernet or Serial - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 70
did not require a password to access the management via the Serial line. With V4.0.0 and higher, a password is required to use the Serial line, similar to using the admin level telnet or admin level web tools. 1. Login to the switch as the admin user. 70 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 71
Enter to commit the configuration to the firmware. Note: Save your passwords in a safe place. It is nearly impossible to access a switch without knowing the switch password. Configuring the IP and Fibre Channel Address The SAN Switch 2/32 is shipped with a default IP address of 10.77.77.77. Use - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 72
the Firmware Version Use these steps to display the SAN Switch 2/32 firmware version. 1. Login to the switch as the admin user. 2. At the command line enter the following command: version This command displays the Kernel version, and Fabric OS release number. 72 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 73
zones. Displaying Switch Configuration Settings Use these steps to display the system configuration settings. 1. Login to the switch as the admin user. 2. At the command line enter the following command: configShow The system configuration settings display. SAN Switch 2/32 Installation Guide 73 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 74
error messages, refer to the HP StorageWorks Fabric OS Procedures Version 3.0.x/4.0.x User Guide. Additional Diagnostic Tests The SAN Switch 2/32 uses diagnostic tests to help troubleshoot hardware and firmware. The diagnostic tests provided on the switch include tests of internal connections and - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 75
orientation during installation. Replacement instructions are provided with all replacement units ordered. Note: The SAN Switch 2/32 uses two AC power cords. To remove all power from the switch, disconnect both power cords before servicing. Power Supplies The two power supplies are hot-swappable - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 76
Managing the SAN Switch 2/32 The Fabric OS identifies the power supplies as follows (viewing the switch from the non-port side): ■ Power supply #1 is on the right when viewing the switch from the non-port side. ■ Power supply #2 is on the left when viewing the switch from the non-port side. To - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 77
, first check the Switch Power/Status and Port Status LEDs. Next, run diagnostics (refer to the HP StorageWorks Fabric OS Procedures Version 3.0.x/4.0.x User Guide). If the motherboard assembly appears to require replacing, contact your switch supplier. SAN Switch 2/32 Installation Guide 77 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 78
Managing the SAN Switch 2/32 78 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 79
Firmware 4 This chapter covers the following topics: ■ Backing Up System Configuration Settings, page 80 ■ Restoring the System Configuration Settings, page 81 ■ Upgrading or Restoring Switch Firmware, page 82 ■ Downloading Firmware from the HP Website, page 83 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 80
the system will prompt you for each parameter, as follows: Example: switch:admin> configupload Server Name or IP Address [host]: 123.45.678.901 User Name [user]: kelev File Name [config.txt]: switch1 Protocol (RSHD or FTP) [rshd]: ftp Password: upload complete 80 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 81
used to log into this computer, path_filename is the path location and filename of the configuration file, and password is the password for the user ID specified. The password operand is only required if you are using FTP. 5. Reboot the switch, type: fastBoot SAN Switch 2/32 Installation Guide 81 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 82
, path_filename is the path location and filename of the new firmware file, and password is the password for the user ID specified. The password operand is only required if you are using FTP. 4. Reboot the switch by entering the following command: fastBoot 82 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 83
and Upgrading Firmware Downloading Firmware from the HP Website To download the firmware from the HP website, go to http://www.hp.com/support. The HP StorageWorks SAN Switch software CD contains the switch firmware, loaders, and downloading instructions. SAN Switch 2/32 Installation Guide 83 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 84
Backing Up the Configuration and Upgrading Firmware 84 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 85
Technical Specifications This appendix covers the following topics: ■ Dimensions, page 86 ■ Power Supply Specifications, page 87 ■ Environmental Requirements, page 88 ■ Memory Specifications, page 89 ■ Serial Port Specifications, page 90 A SAN Switch 2/32 Installation Guide 85 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 86
Technical Specifications Dimensions Table 7 lists SAN Switch 2/32 dimensions. Table 7: Physical Specifications Dimension Height Depth Width Weight (with both power supplies) Value 2.58 in (65.5 mm) 23.06 in (585.6 mm) 16.87 in (42.86 cm) 35.8 lb (16.2 kg) 86 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 87
Active power factor correction per EN61000-3-2 220 watts / 0.8 x 3.412 Btu/hr/watts = 938 Btu/hr Maximum of 15 amps for periods longer than 300 microseconds, at 50 degrees Celsius, hot or cold start Fused in both hot and neutral lines, using independent fuses . SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 88
10×C to 40×C -25×C to 70×C 20% to 85% RH non condensing, at 40×C, with maximum gradient with 10% per hour 10% to 850% RH non-condensing, at 70°C 0 to 3 km above sea level 0 to 12 km above sea level 80 G, 2.4 ms, half sine 20 G, 11 ms, half sine wave 88 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 89
128 MB per switch ■ Flash Memory: 32 MB ■ Boot Flash: 512KB of 8-bit for system boot ■ Compact Flash: 256 MB The centralized memory maximizes the overall switch throughput by guaranteeing full transmit and receive bandwidth to all Fibre Channel ports at all times. SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 90
supported; if pin 7 is used, the signal must always be driven high, using the pinouts listed in Table 10. .Table 10: Cabling Pinouts if Pin 7 is Used PIN 1 2 3 4 5 6 7 8 9 Signal Description TxData RxData Transmit Data Receive Data GND Logic Ground CTS Clear to Send 90 SAN Switch 2/32 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 91
enabled, so it is not necessary to change the Core Switch PID format on these switches. For example, the HP StorageWorks SAN Switch 2/32 and HP StorageWorks Core Switch 2/64 always use Core Switch PID format 1. This parameter is always 1 and cannot be changed. SAN Switch 2/32 Installation Guide 91 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 92
, the Core PID update can take place without application downtime. To ensure maximum ease of administration, this parameter can and should be proactively set on a fabric before it ever enters production, whether or not an upgrade to larger switches is planned. 92 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 93
. 1. Back up all data. Verify backups. 2. If the multi-pathing software cannot automatically switch over between fabrics seamlessly enough for the users of the SAN, use the software's administrative tools to manually disassociate, or mark offline all storage SAN Switch 2/32 Installation Guide 93 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 94
. 7. One at a time, re-enable the switches in the updated fabric. In a core/edge network, enable the core switches first. 8. Once the fabric has re-converged, update with the new Core Switch PID format. 9. Repeat steps 3 through 6 for all fabrics in the SAN. 94 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 95
: The [0] value shown above indicates the Core Switch PID parameter set on this particular switch. f. Type 1 to update the Core Switch PID format. g. Continue to press Enter until you have completed the configure section and have returned to the admin prompt. SAN Switch 2/32 Installation Guide 95 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 96
re-enable the switches in the updated fabric. In a core/edge network, enable the core switches first. 6. Once switch PID format is set, it is stored in the flash memory of the switch, and it is NOT necessary to set it again during subsequent firmware upgrades. 96 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 97
all switches in the fabric and verified that it has re-converged properly, issue the command cfgEnable [effective zone configuration] on one of the switches in that fabric. For example: cfgEnable my_zones 13. Clean the lvmtab file by using the command vgscan. SAN Switch 2/32 Installation Guide 97 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 98
Core Switch /dev/dsk/c64t8d0 /dev/dsk/c64t9d0 16. Activate the volume groups using vgchange. The HP DVD 20. Validate that the entry has been removed by using the command ioscan -funC disk. Notice in the figure below that the NO_HW entry is no longer listed. 98 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 99
fcs0 7. Login into each switch in the fabric. 8. Issue the switchDisable command. 9. Issue the configure command. Change the Core Switch PID Format to 1. 10. Issue the configenable, (effective_zone_configuration) command. For example: configenable my_config SAN Switch 2/32 Installation Guide 99 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 100
PID Format 11. Issue the switchEnable command. Enable the core switches first, then the edge switches. 12. Rebuild the device entries for the affected fabric using you are using multi-pathing software, re-enable the affected path. 16. Repeat for all fabrics. 100 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 101
Statement (Japan), page 106 ■ BSMI EMC Statement (Taiwan), page 107 ■ RRL EMC Statement (Korea), page 108 ■ Laser Safety, page 109 ■ Battery Replacement Notice, page 110 C SAN Switch 2/32 Installation Guide 101 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 102
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this case the FCC could void the user's authority to operate the equipment. Regulatory Series Number: NA2106 102 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 103
Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la Classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. SAN Switch 2/32 Installation Guide 103 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 104
Regulatory Compliance Notices EMC Statement (European Union) This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures. 104 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 105
Regulatory Compliance Notices Germany Noise Declaration Schalldruckpegel Lp = 46.1 dB(A)Am Arbeitsplatz (operator position) Normaler Betrieb (normal operation) Nach ISO 7779:1999 (Typprüfung) SAN Switch 2/32 Installation Guide 105 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 106
Regulatory Compliance Notices VCCI EMC Statement (Japan) 106 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 107
BSMI EMC Statement (Taiwan) Regulatory Compliance Notices SAN Switch 2/32 Installation Guide 107 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 108
Regulatory Compliance Notices RRL EMC Statement (Korea) 108 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 109
Certificate (Worldwide) B. Product Information Each communications port consists of a transmitter and receiver optical not considered hazardous. WARNING: There are no user maintenance operations, service operations, or adjustments to be performed on SAN Switch 2/32 Installation Guide 109 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 110
, battery packs, and accumulators should not be disposed of with the general household waste. In order to forward them to recycling or proper disposal, please use the public collection system or return them to HP, your authorized HP partners, or their agents. 110 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 111
port. Alias Server A fabric software facility that supports multicast group management. API Application Programming Interface; defined protocol that allows applications to interface with a set of services for a response before beginning loop initialization. SAN Switch 2/32 Installation Guide 111 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 112
path between two ports. Consists of two virtual circuits capable of transmitting in opposite directions. See also Link. Command Line Interface that depends entirely on the use of commands, such as through telnet or SNMP, and does not involve a GUI. 112 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 113
-to-end Credit; the number of receive buffers allocated by a recipient port to an originating port. Used by Class 1 and 2 services to manage the exchange of frames across the fabric between source and destination. See also End-to-end Flow Control, BB_Credit. SAN Switch 2/32 Installation Guide 113 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 114
F_Port Fabric Port; a port that is able to transmit under fabric protocol and interface over links. Can be used to connect an N_Port to a switch. Fabric Channel Transport A protocol service that supports communication between Fibre Channel service providers. 114 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 115
to the Fibre Channel. Set the gateway address on one switch to the Fibre Channel IP address of another switch to enable the other switch to forward IP traffic to the Ethernet port on the second switch. Gbps Gigabits per second (1,062,500,000 bits/second). SAN Switch 2/32 Installation Guide 115 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 116
of time required to transmit a frame, from the time it is sent until it arrives. Link Services A protocol for link-related actions. Link As applies to Fibre Channel, a physical connection between two ports, consisting of both transmit and receive fibres. 116 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 117
A set of devices connected in a loop to a port that is a member of another loop. MIB Management Information port, then enters the Open state. Open Recipient The L_Port that receives the OPN ordered set from the open originator, and then enters the Open state. SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 118
Channel port. Communicated during login and port discovery. POST Power On Self-Test; a series of tests run by a switch after it is turned on. Private Device A device that supports arbitrated loop, and can communicate with either private or public NL_Ports. 118 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 119
support 20-bit addresses (or has 20-bit phantom addresses created for it by the switch). Routing The assignment of frames to specific switch ports, according to frame destination. RR_TOV Resource Service Rate The rate at which an entity can service requests. SAN Switch 2/32 Installation Guide 119 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 120
circuits with multiple ports without reentering the arbitration cycle for each circuit. This state can only be accessed by an L_Port in the Open state. Translative Mode A mode in which private devices can communicate with public devices across the fabric. 120 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 121
a specific function in the fabric. UDP User Datagram Protocol; a protocol that runs on top of IP and provides port multiplexing for upper-level protocols. ULP_TOV Upper-level within the loop. A port in the XMITTED CLOSE state cannot attempt to arbitrate. SAN Switch 2/32 Installation Guide 121 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 122
partitioning of the fabric into logical groupings of devices. Devices in a zone can only access and be accessed by devices in the same zone. 122 SAN Switch 2/32 Installation Guide - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 123
the admin password 70 changing the admin user ID 70 checking results 46 configuration settings 81 configuring domain ID 54 status policies 54 configuring the IP and fibre channel address 71 connecting 51, 56 connecting AC power 45, 47 conventions document 11 SAN Switch 2/32 Installation Guide Index - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 124
15 H hardware features 18 help, obtaining 15 HP authorized reseller 15 storage website 15 technical support 15 Hyperterminal 48, 49 I illustrations package contents 24 inner slide rails 32 installation installing the switch as a stand-alone unit 30 installing 31, 32, 34, 35, 38, 58 interpreting 62 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 125
text symbols 11 three hole bar nuts 35 tips for installing 32 U upgrading or restoring the switch firmware 82 V verifying operation 57 voltage 29 W warning rack stability 14 symbols on equipment 12 websites HP storage 15 weight, switch 86 Z zoning summary 18 SAN Switch 2/32 Installation Guide 125 - HP StorageWorks 2/32 | SAN switch 2/32 version 4.0.x installation guide - Page 126
Index 126 SAN Switch 2/32 Installation Guide
installation
guide
hp
StorageWorks
SAN switch 2/32
Product Version:
4.0.x
Second Edition (February 2003)
Part Number:
AA-RTQVB-TE
This installation guide provides basic procedures for setting up, configuring, and managing the
SAN Switch 2/32 and SAN Switch 2/32 Power Pak models.